The automotive industry expects more support from suppliers in quality assurance for assembly work. As a result, suppliers in the automotive industry are looking to automation partners to better meet this technology demand while delivering faster. Mechanical engineering companies need more applications in standard tasks ...

1. Hydraulic pump: Straight shaft swash plate piston pumps are divided into two types: pressure oil supply type and self-priming oil type. Most of the pressure oil supply hydraulic pumps use oil tanks with air pressure, and there are also hydraulic pumps with oil replenishment sub-pumps to provide pressure oil to the oil inlet of the hydraulic pump. The self-priming oil energy of the self-priming hydraulic pump ...

(1) HD (Hydraulic Variable) Type: Adjust the output torque and speed by controlling the swing angle of the motor block with external hydraulic oil. (2) HA (Pressure Variable) type: When the pressure reaches the set value, the motor changes the swing angle with the change of load, thereby changing the output torque and speed. Among them, the main one is constant pressure type (HA1) ...

DAMBACH has developed a new shuttle system based on the compact control system from Bosch Rexroth A leap forward in the dynamics and efficiency of high-level compartment warehouses Tried and tested Flexible and scalable for greater displacement and degrees of freedom ...

1. Cause of failure: the oil level of the hydraulic oil tank is too low; Exclusion method: Add hydraulic oil. 2. Cause of failure: Hydraulic oil is not used according to the season; Exclusion method: Usually suitable for 46# hydraulic oil (or 68#) without special replacement, consider using it when it is cold in the north in winter...

9. Cause of failure: "left-handed" oil pump is installed with "right-handed", resulting in damage to the skeleton oil seal; Exclusion method: the "right-handed" pump cannot be installed on the "left-handed" machine, otherwise the skeleton oil seal will be damaged; 10. Cause of failure: The hydraulic oil is too dirty. Exclusion Method: Cleaning System, ...

1. Adjust the displacement of the pump: The larger the displacement of the hydraulic piston pump, the greater the flow and pressure. The displacement can be adjusted by replacing the displacement of the pump or adjusting the eccentricity distance of the pump. 2. Adjust the valves in the hydraulic system: The valves in the hydraulic system can control the flow and pressure.

1. The pump device, composed of a motor and an oil pump, is the power source of hydraulic pressure and the "heart", and its role is to convert mechanical energy into the power of the cylinder to realize the lifting of goods. 2. The combination valve is a flat valve installed on the vertical plate, and its function is to adjust the direction, pressure and flow rate of the hydraulic oil.

1. First of all, adjust the pressure adjustment screw of Rexroth variable hydraulic pump relief valve to the loosest state, adjust the minimum flow limiter to the minimum state (the upper hydraulic cylinder adjusting screw is adjusted to the loosest state), adjust the flow control valve adjusting screw to the tightest state, and connect a flow rate in series after the relief valve.

Future-proof digitalization and automation technologies must be open, flexible, easily scalable, and secure at the same time. Whether it's mechanical and systems engineering, building and energy automation, the convergence of IT and OT applications is strongly supported and promoted by industry players. As the first system ...

(1) Insufficient inhalation The reason is that the resistance in the suction line of the Rexroth piston pump is too high or the oil replenishment is insufficient. For example, the speed of the pump is too large, the liquid level in the oil tank is too low, the oil inlet pipe is leaking, and the oil filter is blocked. (2) The amount of leakage is too large The reason is the gap in the Rexroth piston pump ...

1: Disassemble the proportional valve Unscrew the nut and slide out of the coil to remove the coil from the proportional end. Use a wrench to loosen and remove the tube. Remove the spring and slide the hex wrench from the tube. Then remove the spool from the valve. 2: Check the fatigue of all individual parts of the proportional valve, grinding ...

Power outage handling If the power supply is instantaneously blacked out or the voltage drops to show "undervoltage", or the instantaneous overvoltage shows "overvoltage", it will cause the Rexroth inverter to trip and shut down, and it will be restarted only after the power supply returns to normal. External fault handling If you enter ...

Analysis of abnormal heating fault of vane pump: 1. The oil temperature is too high 2. The oil cat degree is too large and the internal leakage is too large 3. The working pressure is too high 4. The oil return port is directly connected to the pump population Abnormal heating elimination method of vane pump: 1. Improve the heat dissipation conditions of the fuel tank or use cooling ...

One. Wrong installation method: 1. The coupling is too tight: Because the coupling and shaft fit clearance is too small or no backlash, the bearing will be damaged when struck hard, resulting in early bearing damage and affecting the life of the entire pump core. 2. Axial force on the shaft head: Because...

1. Aging of circuit board components: The components in the Rexroth servo motor circuit board may have problems such as aging and damage as the use time increases, resulting in the circuit board not working normally. 2. Poor circuit board contact: Rexroth servo motor circuit board is connected with other equipment.

Space-saving design: The measuring sensor is fully integrated into the slide Cost-effective position measurement system for a wide range of product sizes From design to service, save time and money 　　Integrated absolute position measurement is used in a wide range of applications, due to its high water ...

Machine builder ILLIG makes the ever-changing food packaging industry more flexible and forward-looking with the openness of the Bosch Rexroth Automation Toolkit ctrlX AUTOMATION technology. 　　Debut at Interpack 2023: the modular ILLIG XLU complete series ...

A new reference process for gluing tasks has been added to the LinSelect configurator Just enter a few parameters to get specific product recommendations Complete subsystems for handling and gluing tasks 　　Thanks to the intelligent reference process in the LinSelect selection software, 　　 ...

1. The pump does not absorb oil, the flow rate is not enough, the pump is empty, and the pump is damaged. Damaged pumps, damaged skates or damaged ski and column ball joint seals; swash plate wear; wear of plungers and cylinder bores; failure of variable mechanisms; Wear of the oil distribution pan or wear of the oil distribution end face of the cylinder block; The LS valve of the pump is worn, the pressure is cut off...