Rexroth's autonomous mobile robot wins the LogiMAT "Best Product" award

(1) Rexroth DBD direct acting relief valve: DBD valve is a direct-acting relief valve, which is used to limit the system pressure, with a total of 7 pressure levels: 2.5, 5, 10, 20, 31.5, 5, 40 and 63Mpa. The types of pressure adjustment are: adjustment handle, adjustment handle with lock, and adjustment screw with protective cover.

1. When the hydraulic pump is started, it should be jogged several times, and after the oil flow direction and sound are normal, it should run under low pressure for 5-10min, and then put into normal operation. Before the piston pump is started, the pump must be filled with clean working oil through the oil drain port on the casing. 2. The viscosity of the oil is affected by the temperature ...

Space-saving design: The measuring sensor is fully integrated into the slide Cost-effective position measurement system for a wide range of product sizes From design to service, save time and money 　　Integrated absolute position measurement is used in a wide range of applications, due to its high water ...

1. Closed-loop hydrostatic drive swash plate axial piston variable pump; 2. The flow rate is proportional to the driving speed and displacement, and can be a stepless variable; 3. With the change of the swing angle of the swash plate, the flow rate increases from 0 to the maximum; 4. The swash plate swings in the middle position, which can be ...

1. Direct-acting relief valve How it works: The hydraulic force and the spring force are directly balanced to control the opening and closing action of the valve core, so as to ensure that the pressure of the oil inlet is basically constant. Peculiarity: (1) The hydraulic pressure of the valve core is balanced by the spring force, so when the system pressure is very high...

1. Remove the mold and cancel the express and trivial mold operation 2. Cancel the low-pressure trivia mold. 3. Close the safety door. 4. Adjust the CNC high-speed mold speed to the value of 0, and adjust the CNC high-speed mold opening speed and CNC low-speed mold opening speed to the value of 40. 5. Starter oil ...

There are three main types of hydraulic pumps: gear pumps, vane pumps and piston pumps. 1. Gear pump: Advantages: small size, simple structure, less strict requirements for the cleanliness of the oil, and cheaper price; Defects: However, the pump shaft is subject to unbalanced force, serious wear, and leakage.

A new reference process for gluing tasks has been added to the LinSelect configurator Just enter a few parameters to get specific product recommendations Complete subsystems for handling and gluing tasks 　　Thanks to the intelligent reference process in the LinSelect selection software, 　　 ...

Technical parameters 1) Select the valve port and model according to the requirements of the medium flow direction and the pipeline connection mode; 2) According to the flow rate and valve Kv value to select the nominal diameter, can also choose the same pipe inner diameter; 3) Working pressure difference: The minimum working pressure difference is above 0.04Mpa.

The automotive industry expects more support from suppliers in quality assurance for assembly work. As a result, suppliers in the automotive industry are looking to automation partners to better meet this technology demand while delivering faster. Mechanical engineering companies need more applications in standard tasks ...

1. Determine the use of Tiaohua Determine the necessary conditions in order to calculate the loads acting on the linear guide 2. Choose the right type Select the type that meets the criteria and pre-select the possible specifications 3. Calculate the applied load Calculate the ...

1. Aging of circuit board components: The components in the Rexroth servo motor circuit board may have problems such as aging and damage as the use time increases, resulting in the circuit board not working normally. 2. Poor circuit board contact: Rexroth servo motor circuit board is connected with other equipment.

First wash. The first cleaning of the hydraulic system of the Rexroth Rexroth hydraulic pump is carried out after the pre-installation (trial assembly of the pipes) and the dismantling of the entire pipeline. The first cleaning should ensure that a large number of metal burrs and powders, sand dust, ...

Rexroth piston pump failure manifests itself as follows. The causes and elimination methods of excessive working noise of piston pumps. There is air in the oil pump. This failure usually occurs when a new pump is installed. When opening a new pump, oil should be added to the pump first to lubricate the pump's bearings, plungers, and cylinders. ...

1) Preparation for cleaning. (1) Preparation of cleaning oil. The cleaning oil can be selected as Rexroth Rexroth hydraulic pump hydraulic system working oil or test oil for the machine to be cleaned. It is not allowed to use kerosene, gasoline, alcohol or steam as the cleaning medium, so as not to corrode the hydraulic components, pipelines ...

1) Remove the protective covers on both sides of the flange end, and rinse and clean the valve when the valve is fully open. 2) Before the installation of the balance valve with actuator, the whole machine should be tested according to the specified signal (electricity or gas) (to prevent the vibration caused by transportation from affecting the performance).

With the combination of sensor systems and six degrees of freedom independent kinematics, the Bosch Rexroth Smart Flex Effector compensation module gives industrial robots a human-like sense of touch, providing automation for processes that were difficult to handle or had to be performed manually in the past.

A10VO series variable piston pump is one of Rexroth variable piston pumps, A10VO series is Rexroth medium pressure series swash plate axial piston pump, nominal pressure 280bar, used in open hydraulic circuits, the pump is very widely used, is used in various fields, including but not limited to...

Thanks to the die pad function of the new standard IH04 E standard module from Bosch Rexroth, engineers can use the most common switching systems. These modules are DGUV-tested and certified with a standardized safety concept and are able to meet general safety requirements at the lowest possible cost. Users can optionally set such ...

Bosch Rexroth Co., Ltd. ("Bosch Rexroth") and Wuxi Weifu High-Tech Group Co., Ltd. ("Weifu Group"), located in Wuxi, Jiangsu Province, China, plan to cooperate to establish a joint venture that aims to combine the strengths of both companies and create a joint venture for ...