Buke servo motor - how to correctly select the servo motor

1. According to the type of working power supply: it can be divided into DC motor and AC motor. 1) DC motors can be divided into brushless DC motors and brushed DC motors according to their structure and working principle. Brushed DC motors can be divided into: permanent magnet DC motors and electromagnetic DC motors.

1. Servo motor pulse control mode In some small stand-alone equipment, the use of pulse control to achieve the positioning of the motor should be the most common application method, this control method is simple and easy to understand. The basic control idea: the total pulse amount determines the motor displacement, and the pulse frequency determines the ...

1. Sweeping: Sweeping is generally caused by friction of the stator and rotor due to bearing damage, shaft bending, or improper assembly during maintenance. In the process of overhaul and assembly of the motor, the parts of the motor should be kept clean, and the assembly of the end cover, bearing, etc. should be reasonable and not barbaric construction, otherwise ...

In terms of the response speed of the servo drive: the torque mode has the smallest amount of calculation, and the driver responds the fastest to the control signal; The position mode is the most computationally intensive, and the driver is the slowest to respond to the control signal. When there are relatively high requirements for dynamic performance in motion, it is necessary to ...

(1) Azimuth share gain Sets the share gain of the azimuth ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the azimuth lag under the same frequency command pulse. However, too large a value may cause vibration or overshoot. The parameter values are determined by the detailed servo ...

1. Start the servo motor before work (1) Measure the insulation resistance (0.5M or more for low-voltage motors). (2) Measure the power supply voltage, check whether the wiring of the motor is correct, and whether the power supply voltage meets the requirements. (3) Check whether the starting device is normal. ( ...

The stepper motor is a discrete motion device, which is intrinsically related to modern digital control technology. In the domestic digital control system, the stepper motor is widely used. With the advent of all-digital AC servo systems, AC servo motors are also increasingly used in digital ...

Reasons for the shutdown of the speed up Buke motor due to contamination: 1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause the bearing and the ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

B3: The base has feet. The end cap has no flange. Mounted on foundation members. B35: The frame has feet. Flange on the end cap. The flange has through holes. It is installed on the foundation member by a foot and attached to the flange mounting. B34: The frame has feet. The end cap has a flange and a screw on the flange.

1. The power of the motor 2. The power supply voltage of the motor 3. The encoder type of the motor 4. The size of the base of the motor 5. The movement mode of the motor 6. Motor communication bus 7. Whether the motor is equipped with a brake mechanism 8. Motor driver class ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

6. The motor vibrates greatly during operation (1) The cause of the failure (1) Due to excessive clearance of worn bearings; (2) uneven air gap; (3) Rotor imbalance; (4) Bending of the rotating shaft; (5) The coaxial axis of the coupling (pulley) is too low. (2) Troubleshooting ...

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

Buke touch screen programming software is a professional touch screen programming software, support for MT505T, MT506MV, MT508T, MT510T and other models, can assist users in the extreme time to grasp its planning methods, very suitable for modern industry increasingly large workload and function ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

Human-computer interaction refers to the interaction between humans and machines, which is essentially the interaction between humans and computers. Or more broadly: human-computer interaction refers to the interaction between a human and a machine containing a computer. Specifically, the two-way communication between the human-computer interaction user and the machine containing the computer ...