1. Number of joints. The number of joints can also be called degrees of freedom, which is an important indicator of the flexibility of the robot. Generally speaking, the robot workspace can reach three degrees of freedom, but welding not only needs to reach a certain position in the space, but also needs to ensure the spatial attitude of the welding gun. ...

One. Daily inspection and maintenance 1. Wire feeding mechanism. Including whether the wire feeding force distance is normal, whether the wire feeding conduit is damaged, and whether there is an abnormal alarm. 2. Whether the gas flow rate is normal. 3. Whether the welding torch safety protection system is normal. (It is forbidden to close the welding torch safety protection work) 4. The water circulation system works ...

1. Failure of the operating system. That is, the soft fault of the automatic welding robot, often data loss or the operating system can not be started, the automatic welding robot has a protection function, can send an alarm signal to the fault source, only need to repair the fault according to the alarm reminder, in case the data ...

1. Welding deviation. The cause of welding deviation: welding deviation is that the welding angle deviates from the weld in the process of welding operation, and the welding is not carried out along the weld. Welding deviations can be caused by incorrect torch finding points or incorrect torch positioning. Actions to be taken in the event of a weld deviation: the operator ...

(1) Arc welding robot system optimization and integration technology: The arc welding robot adopts AC servo drive technology and high-precision, high-rigidity RV reducer and harmonic reducer, which has good low-speed stability and high-speed dynamic response, and can realize maintenance-free function. (2) Coordinated control ...

a) Number of axes in the system (sum of linkage and non-linkage shafts) b) Number of linkage axes c) Dimensions and weight d) Power source parameters and total power e) Number of axes of the robot body f) The number of shafts and structural form of welding positioner g) Number of axes of the moving device ...

1. Stabilize and improve the welding quality to ensure its uniformity. When using robot welding, the welding parameters of each weld are constant, and the quality of the weld is less affected by human factors, which reduces the requirements for the operation technology of workers, so the welding quality is stable. And when manual welding ...

1. Robots 2. Automatic wire feeding device 3. Welding power supply 4. a welding gun 5. a positioner 6. Tooling fixtures

1. The structure of the conveyor belt feeding at the front end of the claw of the palletizing robot generally has a national standard for the roller conveyor belt for bag grabbing, and it is necessary to adopt a standard interface, and for the belt conveyor belt, it is necessary to consider how to achieve it. 2. The selection of the palletizing robot model, the load capacity of the robot ...

1. Simple structure and few parts. As a result, the failure rate of parts is low, the performance is reliable, the maintenance is simple, and the required parts are less in stock. 2. Occupies a small area. It is conducive to the layout of the production line in the customer's plant, and can set aside a large warehouse area. The palletizing robot can be set ...

1. The personnel who need to repair the palletizing robot must be relevant personnel, at least those who often use the machine or have been trained and carefully read the machine manual; 2. Remove the filter of the air source triplet, empty the air source pipeline of the purge manufacturer, and then supply the air source; ...

Welding velocity refers to the linear velocity of the arc moving along the welded joint. All other things being equal, a medium welding speed is the maximum penetration depth. As the welding speed decreases, the amount of deposited metal per unit length of weld increases. At very slow welding speeds, the welding arc impinges on the weld pool, not the base metal. ...

The important condition of welding forming is to set the welding parameters: basic parameters such as current, voltage, time, and special functional parameters such as restart, arc detection, preparatory air supply, and water cooling abnormality, etc. The selection of welding parameters is more difficult, because the various welding parameters are not isolated, but mutually ...

Effect of changes in electrical parameters of welding on the quality of welding: 1. Welding current When the welding current increases (other conditions remain unchanged), the penetration depth and residual height of the weld increase, and the melting width remains unchanged (or slightly increases) for the following reasons: (1) When the current increases, the arc on the workpiece ...

1. Carry out correct debugging. Before using the arc welding robot for welding work, it is necessary to debug the work, adjust the welding parameters according to the specifications of the weldment and the welding environment, observe whether the weld is well filled, and if there are welding defects, it needs to be checked and corrected in time.

1. Welding deviation problem: It may be caused by incorrect welding position or problems when looking for the welding gun. At this time, it is necessary to consider whether the position of the center point of the welding torch is accurate and adjust. If this happens often, it is necessary to check the zero position of each axis of the welding robot and recalibrate ...

1. Gas arc welding: Argon arc welding, which uses argon as the shielding gas in the welding area, and carbon dioxide shielded welding, which uses carbon dioxide as the shielding gas in the welding, are all gas-shielded arc welding. The basic principle is that when welding with an electric arc as a heat source, ...

(1) Stabilize and improve the welding quality to ensure its uniformity. When using robot welding, the welding parameters of each weld are constant, and the quality of the weld is less affected by human factors, which reduces the requirements for the operation technology of workers, so the welding quality is stable. And when manual welding ...

1. High work efficiency The column robot palletizer grabs 300-400 times per hour, and you can choose between single and double claw hands, and the speed and quality are much higher than manual labor. 2. High operation accuracy and large working range. The column robot palletizer occupies a small area, and the action ...

(1) Arc welding robot system optimization and integration technology: The arc welding robot adopts AC servo drive technology and high-precision, high-rigidity RV reducer and harmonic reducer, which has good low-speed stability and high-speed dynamic response, and can realize maintenance-free function. (2) Coordinated control ...

1) Number of axes in the system (sum of linkage shafts and non-linkage shafts) 2) Number of linkage axes 3) Dimensions and weight 4) Power source parameters and total power 5) The number of axes of the robot body 6) The number of shafts and structural form of welding positioner 7) Number of axes of the mobile device ...