Estun Robot - Common faults and troubleshooting methods of palletizing robots

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

1. Select magnet wires with good corona resistance to meet the requirements of high-frequency pulse resistance and partial discharge of the motor. Generally, polyesterimide/polyamideimide composite layer enameled wire is used, which is corona resistant and corona resistant magnet wire. Second, winding, embedded wire construction technology. Frequency conversion...

A servo control system is a feedback control system that is used to accurately follow or reproduce a process. In many cases, the servo system refers specifically to the feedback control system in which the controlled quantity (the output of the system) is the mechanical displacement or displacement velocity and acceleration, and its function is to make the mechanical displacement of the output (or ...

1. Estun servo motor maintenance - overload alarm A04 1. The wiring of the servo motor is wrong or the wiring is leaking (1) The U, V, and W phase wires of the motor are connected incorrectly (2) Whether the insertion of the connector on the servo motor side is defective 2. The model of the servo drive and the motor does not match ...

Precautions for servo motors: 1. Protection of servo motor oil and water A: The servo motor can be used in places where it will be attacked by water or oil droplets, but it is not fully waterproof or oil-proof. Therefore, servo motors should not be placed or used in water or oil-infested environments. ...

Advantages and disadvantages of AC servo motors Advantages: good speed control characteristics, smooth control over the entire speed zone, almost no oscillation, high efficiency of more than 90%, less heat generation, high-speed control, high accuracy position control (depending on encoder accuracy), rated operating area ...

1. Motor encoder alarm 1. The cause of the failure (1) Wiring fault; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment. 2. Fault cleaning (1) Check the wiring and sweep away the fault ...

1. Different ways of control Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. The workflow is different Stepper motor ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

Servo drive is a kind of controller used to control servo motor, its role is similar to the inverter to ordinary AC motor, as a precision equipment, it will inevitably have some faults in the process of use, common faults and maintenance methods are as follows: 1. When the motor rotates, the LED light ...

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

Generally, there are three control modes for servo: speed control mode, torque control mode, and position control mode. 1. Speed control (1) Speed system, that is, the motor runs according to the given speed command. (2) The application of speed control is quite wide-ranging ...

1. Series motor: The series motor has a high starting torque and a high current. This kind of motor has poor speed regulation. 2. Split series motor: They are motors with some sub-field rates of kilowatts. Split tandem motors have a typical torque-speed profile ...

From the perspective of the protection response speed of the robot servo drive, Estun has a small amount of calculation in the form of torque, and the response to the control signal of the drive is fast. The azimuth form has a large amount of computation, and the response to the driver's control signal is slow. 1. If there is a relatively high demand for dynamic functions in sports...

First, the working principle is different Stepper motor controller: It is an electronic product that can send out a uniform pulse signal, and the signal it sends out enters the stepper motor driver, which will be converted by the driver into a strong current signal required by the stepper motor to drive the stepper motor to run. Stepping ...

CALIB Command: This instruction calibrates joint position sensors. STATUS command: Used to display the status of the user's program. FREE command: This command displays the unused storage capacity. ENABL command: used to turn the system hardware on and off. ZERO Directive: This directive ...

Cause of failure and solution: (1) The phase sequence of the motor is out of order and the encoder is abnormal, check whether the power line of the motor (U, V, W, D) is connected incorrectly, and whether the encoder connection is not in good contact. (2) The motor model parameters do not match, check and reset the server Pn parameters or more...

1. Open the shell of the robot to expose the motor base. 2. Use a screwdriver or wrench to remove the screws on the motor base. 3. Remove the screws, lift the motor base, and disassemble it from the robot. 4. The motor base is tightly connected with the robot, and tools such as wrenches are used.

First, the control accuracy is different The step angle of the two-phase hybrid stepper motor is generally 3.6 ° and 1.8 °, and the step angle of the five-phase hybrid stepper motor is generally 0.72 ° and 0.36 °. There are also some high-performance stepper motors with smaller step angles. Such as Sitong company produced a kind of wire for slow wire ...

6. What should I pay attention to when using the motor? Check the following before powering on: 1) Whether the power supply voltage is appropriate (overvoltage is likely to cause damage to the drive module); The +/- polarity of the DC input must not be misconnected, and the motor model or current setting on the drive controller ...