Weiluntong touch screen regular repair faults

Open the Veriton touch screen programming software, select [Common] in the main interface and open it In the Common drop-down menu, select System Parameters and click Open. Then select [HMI Attributes] in the pop-up system parameter setting menu and click OK. ...

1. The film surface of the industrial touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product. 2. The industrial touch screen part is a glass product, and the corners of the glass are sharp, please wear gloves and finger sleeves when assembling. 3. The industrial touch screen part is fragile glass ...

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

Advantages of infrared touch screen: 1. High stability, will not drift due to changes in time and environment 2. Highly adaptable, not subject to current, voltage and static interference, suitable for some harsh environmental conditions (explosion-proof, dust-proof) 3. High light transmittance, no ...

The default standby time is 1 minute. The specific steps are as follows: 1. First of all, open our touch screen editing software, and be sure to select the software corresponding to the touch screen model. 2. Edit the touch screen screen we need. 3. Open the common menu in the upper left corner ...

1. Check if the touch screen is clean: If there are stains or grease on the surface of the touch screen, it will cause the touch to be insensitive or slow to respond. The touchscreen surface can be cleaned using a specialized touchscreen cleaner or a clean cloth. 2. Check if the touch screen is damaged: If the touch screen surface is damaged, ...

1. Software use issues 1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4 ...

25. Bit status switch switch, bit status indicator, equipment linkage: Through the bit state switching switch element OFF->ON, the macro command is executed: the bit status indicator is set to the ON state; Select the execution macro through the PLC control, select the trigger mode ON->OFF, and set the bit ...

1. Can the human-machine interface be connected to the PLC? That's not true. Human-computer interface products are produced to solve the human-computer interaction problem of PLC, but with the development of computer technology and digital circuit technology, many industrial control equipment have serial communication capabilities, so as long as there is ...

1、Player function:The player function is equivalent to the TV at home,At present, some touch all-in-one machines support large-size 4K display,True color full HD display,The display effect is very good。 2. Touch function: The touch all-in-one machine is naturally equipped with touch function, and the screen ...

Method 1: Reconfigure capacitive screen parameters through the configuration file The configuration parameters of the capacitive touch screen are saved in the serial port screen, and the sensitivity of the capacitive touch screen can be configured by writing new parameters. For customers who need to add a panel to a capacitive touch screen, panel samples and structures can be ...

The five-wire resistive touch screen and the four-wire resistive touch screen both adopt the principle of analog resistance, and their conventional fault characteristics are exactly the same as those of the four-wire resistor. If you are using a five-wire resistive touch screen, when there is an installation and maintenance problem, please determine and solve the problem in the following order. ...

The man-machine interface is connected to programmable controllers (PLCs), frequency converters, DC governors, instruments and other industrial control equipment, and the display screen is used to display and write working parameters or input operation commands through input units (such as touch screens, keyboards, mice, etc.) to realize the interaction of human and machine information.

The 7-inch human-machine interface has always been a popular product in the market due to its light size and diverse applications, and it has been in short supply recently. In order to meet the needs of the majority of users for the 7' man-machine interface, Weilun Tong Technology has launched a new 7' man-machine interface: MT8071iP2, which allows users to ...

Precautions when using Verun Tong inverter 　　When shipping and storage During the storage period, it is necessary to ensure that the inverter is not subjected to physical shocks and oscillations. It is also necessary to ensure that they are not exposed to rain and are not placed in places where the ambient temperature is too high. When transferring, hold the bottom of the body ...

5.1 Why does the prompt "EasyWindow must run from EasyManager or EasyBuider" appear when using the offline simulation function? If the serial port is selected as com4 or above (excluding com4), the prompt will be displayed, but it will not affect the download function, ...

(1) FILM - that is, the film used for touch, the base material is PET. When touched, the ITO of the upper and lower layers is brought into contact by deforming the film, resulting in different "resistance values" in the X and Y axes (similar to the principle of moving rheostats). Depending on the requirements of use, the table of FILM ...

With the advent of the Internet of Things (IoT) era, more and more PLCs and controllers support web servers, which are convenient for users to directly modify the content of various system parameters in the equipment and monitor their operating status through the "web interface". In the face of this trend, Weilun Tong new ...

First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the surface of the touch screen for dirt and dirt.

1. Why can't the screen display Chinese normally, but the display is garbled? Answer: This situation is generally caused by not choosing the correct Chinese font, just choose a Chinese font, the specific operation steps are as follows: 1) In EasyBuilder soft...