(1) RH400 size: 48*96, depth 60, about 250g
Details:
●A variety of input types are available:
1) Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
2) Temperature measurement heat resistance input: PT100, JPT100
3) Tributary voltage: DC0 - DC5V, DC1 - DC5V
●Multiple alarm types: upper limit input value, lower limit input value, upper limit deviation, lower limit deviation, upper and lower limit deviation, upper and lower range setting value, lower limit setting value (standby operation can be attached)
●Sampling cycle: 0.5s
●Measurement accuracy: Thermocouple: ± (0.3% of displayed value + 1 digit) or ± 2 degrees Temperature measurement resistance: ± (0.3 + 1 digit of displayed value) or ± 0.8 degree tributary voltage/current input: ± (0.3% of displayed value + 1 digit)
●Control output: relay contact output: 1c contact (AC250 3A) resistance load voltage pulse output: (DC0/12V) allowable load resistance above 600 ohms can be heated and cooled dual output control (output 1: heating side; Output 2: Cooling side)
●Optional heater disconnection alarm and control ring disconnection alarm
(2) CH402 size: 48*96, depth 100, about 250g
Details:
●A variety of input types are available:
1) Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
2) Temperature measurement heat resistance input: PT100, JPT100
3) Tributary voltage: DC0 - DC5V, DC1 - DC5V
4) Tributary current: DC0-20MA, DC4-20MA (250 ohm external resistance required)
●Multiple alarm types: upper limit input value, lower limit input value, upper limit deviation, lower limit deviation, upper and lower limit deviation, upper and lower range setting value, lower limit setting value (standby operation can be attached)
●Sampling cycle: 0.5s
●Measurement accuracy: Thermocouple: ± (0.3% of displayed value + 1 digit) or ± 2 degree temperature measurement resistance: ± (0.3% of displayed value + 1 digit) or ± 0.8 degree tributary voltage/current input: ± (0.3% of displayed value + 1 digit)
●Control output: relay contact output: 1c contact (AC250 3A) resistance load voltage pulse output: (DC0/12V) allowable load resistance above 600 ohms current output: (DC4 - 20MA) allowable load resistance above 600 ohms can be heated and cooled double output control (output 1: heating side; Output 2: Cooling side)
●Optional heater disconnection alarm and control ring disconnection alarm
●Optional 2-wire RS-485 communication
(3) CD901 size: 96*96 depth 100, about 340g
Details:
●A variety of input types are available:
1) Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
2) Temperature measurement heat resistance input: PT100, JPT100
3) Tributary voltage: DC0 - DC5V, DC1 - DC5V
4) Tributary current: DC0-20MA, DC4-20MA (250 ohm external resistance required)
●Multiple alarm types: upper limit input value, lower limit input value, upper limit deviation, lower limit deviation, upper and lower limit deviation, upper and lower range setting value, lower limit setting value (standby operation can be attached)
●Sampling cycle: 0.5s
●Measurement accuracy: Thermocouple: ± (0.3% of displayed value + 1 digit) or ± 2 degree temperature measurement resistance: ± (0.3% of displayed value + 1 digit) or ± 0.8 degree tributary voltage/current input: ± (0.3% of displayed value + 1 digit)
●Control output: relay contact output: 1c contact (AC250 3A) resistance load voltage pulse output: (DC0/12V) allowable load resistance 600 ohms to current output: (DC4 - 20MA) allowable load resistance above 600 ohms can be heated and cooled double output control (output 1: heating side; Output 2: Cooling side) Trigger output for driving TRIAC (three-terminal bipolar thyristor): Trigger mode - zero cross method, on-current: 50 mA (50 degrees), 70 mA (25 degrees) for zero cross type Medium capacity TRIAC (for driving loads below 100 a) *Heating/cooling type is not available for TRIAC (three-terminal bidirectional thyristor) Output: Rated value 0.5 A (ambient temperature 40 degrees Celsius or less)
●Optional heater disconnection alarm and control ring disconnection alarm
●Optional 2-wire RS-485 communication
(4) FB900 size: 96*96*60
Details:
●Abundant input and output
●Automatic/manual, local/remote direct switching
●Multi-storage area function: Up to 8 different setting values can be registered for the master setting value, etc., and cumbersome setting changes can be made in a package. Zones can also be switched via an optional external contact input.
●By combining the multi-storage function, it is possible to connect the number of the other area, the duration of the area, and set the limit of the rate of change, and the program operation can be realized up to 16 segments (8 steps).
●Frequently used data (up to 16 items) can be freely listed in consecutive addresses, so data transmission can be greatly reduced and high-speed communication can be realized.
●Joint operation can be carried out using communication
●PID control: The sampling cycle can be switched to 0.05s, which corresponds to the high-speed heating process. A new type of heat-and-cool PID that inhibits undershoot on the cooling side. You can switch between the controls of "heating, cooling, heating and cooling, and position ratio".
(5) CH102 size: 48*48, depth 100mm, about 170g
Details:
●A variety of input types are available:
1) Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
2) Temperature measurement heat resistance input: PT100, JPT100
3) Tributary voltage: DC0 - DC5V, DC1 - DC5V
4) Tributary current: DC0-20MA, DC4-20MA (250 ohm external resistance required)
●Multiple alarm types: upper limit input value, lower limit input value, upper limit deviation, lower limit deviation, upper and lower limit deviation, upper and lower range setting value, lower limit setting value (standby operation can be attached)
●Sampling cycle: 0.5s
●Measurement accuracy: Thermocouple: ± (0.3% of displayed value + 1 digit) or ± 2 degree temperature measurement resistance: ± (0.3% of displayed value + 1 digit) or ± 0.8 tributary voltage/current input: ± (0.3% of displayed value + 1 digit)
●Control output: relay contact output: 1c contact (AC250 3A) resistance load voltage pulse output: (DC0/12V) allowable load resistance above 600 ohms current output: (DC4 - 20MA) allowable load resistance above 600 ohms can be heated and cooled double output control (output 1: heating side; Output 2: Cooling side)
●Optional heater disconnection alarm and control ring disconnection alarm
●Optional 2-wire RS-485 communication
|
More on that
|
Common faults and solutions of RKC temperature controllers
1. The power indication is normal, but the temperature controller has no screen display. Most of this fault is caused by the heating of the voltage regulator element (7805 or 7812) on the thermostat during long-term use, which leads to the breakpoint of the solder joint, and sometimes it is caused by the phenomenon of virtual soldering at the factory, and the main re-soldering can be done.
2. Temperature controller ...
|
|
RKC Level Gauge – How to properly use a plug-in float level gauge for level measurement
1. Select the appropriate level gauge
First of all, it is necessary to choose the appropriate level gauge. The following factors should be taken into account in the selection of a level gauge:
Measure the properties of the medium: e.g., temperature, pressure, viscosity, corrosiveness, etc.
Measuring range: i.e. the height range of the liquid ...
|
|
Specifications and models of RKC thermostats
CH102 (48×48×100mm)
CH402 (48×96×100mm)
CH902 (96×96×100mm)
1. RH400 size: 48*96, depth 60, about 250g
1. Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
...
|
|
RKC Level Gauge – Four mounting methods for buoy level gauges
1. The buoy level gauge is welded and installed under the guide wire
At the bottom of the container, determine the position according to the requirements of the movement direction of the level gauge buoy, and weld or rivet the support under the fixed guide wire.
2. Buoy level gauge ruler installation
1. The connecting part of the ruler should be flat.
|
|
RLC thermostat – what you should pay attention to when maintaining your temperature controller
1. Do not wipe with acidic, alkaline and other corrosive liquids and water-containing rags when cleaning, so as not to damage the temperature controller and affect its normal use.
2. Do not decorate and cover the temperature controller. The thermostat has a built-in temperature sensor to sense the outside temperature. Therefore, Wen ...
|
|
RKC Thermostat How to properly select and use a pressure sensor
High-temperature melt pressure sensors, transmitters, and high-temperature melt pressure gauges are special equipment in extrusion processing.
On the production line, melt pressure sensors play an important role in improving melt quality, increasing production safety and protecting production equipment.
Use...
|
|
RKC Thermostat – How to Maintain the Instrument?
The normal operation of the instrument is inseparable from the on-site maintenance relationship, especially some important process links, once there is a leak, it will greatly affect the quality of the product, resulting in heavy losses.
First of all, it is common to install both remote and field-indicated level gauges on important tanks.
|
|
RLC thermostat – the wiring method of the thermostat
1. Prepare the thermostat, wires, and thermal resistance, and print out the wiring diagram of the thermostat
2. Use wire strippers to strip off the wire skin, use crimping pliers, and press the wire end to the cold-pressed terminal.
3. Connect the 220V power supply to the inlet terminal of the thermostat, and connect the thermal resistance to the thermostat ...
|
|
RKC thermostat - what should be paid attention to when maintaining the thermostat?
1. Do not wipe with acidic, alkaline and other corrosive liquids and water-containing rags when cleaning, so as not to damage the temperature controller and affect its normal use.
2. Do not decorate and cover the temperature controller. The thermostat has a built-in temperature sensor to sense the outside temperature. Therefore, Wen ...
|
|
RRKC thermostat - common faults and solutions of stand-alone thermostats
Fault 1: The thermostat does not turn on (does not light up)
Analyze the causes
1. Wrong wiring
2. The voltage of the input terminal is not enough or the input terminal is damaged by empty opening and leakage
3. Whether the cable between the panel and the power board is broken or plugged incorrectly
4. Load short circuit or open circuit, probe ...
|
|
Specifications and models of RLC thermostats
CH102 (48×48×100mm)
CH402 (48×96×100mm)
CH902 (96×96×100mm)
1. RH400 size: 48*96, depth 60, about 250g
1. Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L
...
|
|
RKG thermostat - an introduction to the relevant knowledge of temperature controllers
The temperature controller is an electrical switchgear that controls the temperature of an air-conditioned room. The temperature range in the air-conditioned room controlled by the temperature controller is generally 18°C--28°C. The temperature controller commonly used in window air conditioners uses the principle of pressure to push the contacts on and off. Its structure consists of bellows ...
|
|
RK Thermostat - The working principle and device precautions of liquid expansion thermostat
How liquid expansion thermostats work
Liquid expansion thermostat is a physical phenomenon (volume change) that causes the material (generally liquid) in the temperature sensing part of the thermostat to undergo corresponding thermal expansion and cold contraction when the temperature of the controlled object changes, and the diaphragm box connected with the temperature sensing part expands or ...
|
|
RKC thermostat - introduction of three wiring methods of thermal resistance
1. The three wiring methods of Pt100 RTD are different in principle:
The two-wire system and the three-wire system are measured by the bridge method, and the relationship between the temperature value and the analog output value is given after ***. There is no bridge on the four wires, it is completely just sent with a constant current source, measured by a voltmeter, and the test is given after *** ...
|
|
RRKC thermostats – how are temperature controllers wired and commissioned?
1. Take out the room temperature controller, and then connect the power supply terminal of the temperature controller to the power supply according to the terminal diagram of the temperature control chart
2. Then take out the temperature sensor that comes with the temperature controller and detect it
3. According to the temperature controller terminal, the temperature sensor is connected to the controller's transmission.
|
|
RKC Level Gauges - Advantages and Disadvantages of Several Common Level Gauges Introduction
1. Float level gauge is an instrument that relies on the principle of buoyancy to measure the liquid level. Usually by means of a float in conjunction with a scale, the observer can visually read the height of the liquid level.
Advantages: fast and intuitive reading; Low price; Easy to install.
Shortcoming:...
|
|
RKC Level Gauge - Preservation and storage of float level gauges in daily use
1. To avoid damage to the instrument, pay attention to the correct protection method: in order to ensure the accuracy of the instrument and avoid damage to the instrument, try not to use the protection instrument of isolator or other isolation devices. If you have to do it, you should also pay attention to the careful selection, determine the isolation solution, and wash the isolation film correctly, ...
|
|
RLC Thermostat - Fault and Troubleshooting of Vapor Pressure Temperature Controller
Faulting and troubleshooting of vapor pressure temperature controllers
(1) Common faults and common faults of the vapor pressure type temperature controller include contact burning or adhesion, failure of the mechanical transmission mechanism and leakage of temperature sensor in the temperature sensing tube. Its detection method is: put the thermostat knob in a parking position, and use ...
|
|
What problems are easy to encounter in the use of RKCPT100 temperature sensor probes?
What problems are easy to encounter in the use of PT100 temperature sensor probes?
1. Is the output signal unstable?
A: Maybe it's the temperature instability of the temperature source itself, or the problem of on-site disturbance.
2. Is there a big error in the output of the transmitter?
Answer: This ...
|
|
How to set the parameters of RKC thermostat RH900
1. Lower limit deviation alarm setting: press the SET key to select and display "SLP", the green display screen displays the value of the parameter, and select the shift, increment, and decrement keys to set or modify the parameter. This parameter indicates the difference between the alarm point and the master setpoint.
2. The upper limit deviation alarm is set ...
|
|
Contact
working hours
