Fisher/Fisher Pressure Regulator Series 310A

The Fisher DMA/AF is a multi-shaped, mechanically atomized, backpressure-activated superheater interstage desuperheater. Designed for applications that require control of moderate load fluctuations and high thermal cycling. specification Certified PED, CRN Severe service steam conditioning Materials SA105, F22, F91 Job...

Fisher multi-way valves and actuators divert fluid from a single fluid line to a test outlet or sampling device. A single multi-flow selector acts as a manifold that brings together eight fluid lines at once. Actuator is an electronic device designed to control and monitor the operation of multiple flow selectors.

The Fisher M-Series Hand Turbine Actuator is a fully enclosed, all-weather turbine actuator that provides reliable manual operation for the Fisher A11, A31A, and A41 high-performance butterfly valves. The Fisher M Series Hand Turbine Actuator consists of a body shell, cover, turbine, ...

The Fisher TBX-T desuperheater can be used in a variety of applications to effectively reduce the temperature of superheated steam to the ideal set point. The TBX-T can be installed in steam lines with diameters DN 200 to DN 1200 (NPS 8 to 48) and can maintain steam temperatures at 6°C (10° ...

The Fisher Yarway AT-18/28 Heavy Duty A.T.-Temp Desuperheater was developed specifically for medium/high pressure steam applications. Its prefabricated structure can easily meet a variety of boiler specifications and material specifications. The unit can also be used as an injector for liquid injection gases, typically with high-grade alloys such as stainless steel. ...

The Model 92S self-actuated control valve is piston-actuated and can be used in high circulation steam applications. The base of the Model 92S control valve and pilot has an abrasive surface that has been shown to minimize base leakage. Both the 6492H and 6492L commanders are equipped with bellows to reduce guide rod friction ...

Complete Fisher pipe silencers provide superior noise reduction performance for applications where valves generate a lot of noise. Once installed, the total system pressure drop is split between the valve and the silencer. This allows the valve to operate at a lower pressure drop ratio, reducing the noise generated during the flow through the control valve.

Introduction: The Fisher/Fisher A11 High Performance Butterfly Valve is a reliable, high-performance butterfly valve for throttling and switching applications. Available in a pair of clamp or single flange designs to maintain tight shut-off over long periods of time, the valve is specific for a wide range of pressure and temperature conditions, including cryogenic applications.

The Fisher V260 is a full-bore control valve with a bottom-up design that maximizes pressure, flow, and process control. Integral borehole silencers are used to control noise and vibration generated by high-pressure drop liquids and gases. The spline shaft is connected with the actuator, which reduces the movement loss. ...

The Fisher easy-e ET is the ideal solution for all high process temperature general applications, with a balanced plug design and cage guided trims. Available with straight-through or angled bodies, these valves provide up to Class V or Level VI shut-off specification Certified to SIL, fugitive emissions, N...

The Fisher ATST desuperheater is a state-of-the-art solution for desuperheating applications where atomization performance and amplitude of variation are critical. ATST nozzles atomize water through steam atomization to form tiny water droplets that evaporate rapidly over a wide range of vapor flows and conditions. specification Certificates: PED, CRN ...

Introduction: Fisher/Fisher FB welded angle valves control compressible fluids and can be used in special applications that require maximum noise reduction and high flow capacity. Typical applications include main steam pressure reducing valves and compressor bypass valves. FB valves are also commonly used in petrochemical and natural gas processing plants for acidic ...

The Fisher CAV4 valve is designed for clean, cavitation applications with a pressure drop of more than 207 bar (3000 psi). The Cavitrol™ IV trim in the valve is designed to extend the flow area. Each trim stage has a sequentially increasing flow zone. This guarantees a very ...

The Fisher 3610J pneumatic positioner can be used with a single-acting rotary actuator to precisely locate control valves used in throttling applications. These positioners are rugged and provide valve positioning proportional to the pneumatic input signal or DC current input signal and as a whole ...

The Fisher V280 is a three-piece, trunnion-style, full-bore control valve that handles all CL900 pressure drops. Optimized pressure, flow, and process control. An optional borehole silencer controls noise and vibration from high-pressure drop liquids and gases. The spline shaft is connected with the actuator, which reduces the ...

Versatility of application - 5 models and 11 sizes of actuators are available for a wide range of applications. A wide range of spring rates, stroke limiters, and manual operators are available for use in virtually any control valve application. There is an excellent linear relationship between the loading pressure and the stroke.

The Fisher/Fisher Model 630 regulator is designed to provide fast and economical pressure control for a wide range of applications and is suitable for a wide range of gaseous media Specifications: Process Gases/Specialty Gases 　　Fisher pressure control products are suitable for chemical industry processes such as analytical ...

Introduction: The Fisher/Fisher D2T valve is best suited for use as a dump valve for gas separators and scrubbers. It is also suitable for other high-pressure applications in natural gas production, compression and processing. 　　Features: Optional 1 NPT end connection. Have a C ...

The R222 series regulators are certified by Underwriters Laboratories (United States Safety Testing Laboratories, Inc.) for use in LPG two-stage pressure regulating systems. The unit reduces the outlet pressure of the primary regulator (typically from 10 psig / 0.69 bar) to 11-in ...

The Fisher 377 guard valve assists in maintaining routine process operations that require a specific valve or actuator. When the compressed air pressure drops below the trigger point, the guard valve prevents the actuator from rising, locking in the previous position, or not descending. When the compressed air pressure rises above the trigger point, 3 ...