Fisher/Fisher R222 Series Secondary Regulators

Description: The Fisher/Fisher 67C series of high-pressure regulators is a high-pressure regulator for a variety of liquid or vapor applications. The Series 67C basic regulator is equipped with wrench adjustment, handwheel adjustment, dial adjustment pattern with calibration scale or non-adjustable vandal spring ...

The Fisher DVI desuperheater is injected with a water jet at the venturi outlet section to ensure thorough mixing as well as rapid atomization. DVI desuperheaters can be easily installed between flanges in steam pipes from DN25 to DN600 (1 to 24 inches). No moving parts, water fill mode for fast, ...

The Fisher 1061 actuator is used to operate splined shaft rotary control valves such as Fisher Vee-Ball™ valves, eccentric butterfly valves, and butterfly valves. The actuator/body connection of this actuator can be set either as push-down open or push-down as off. In addition, 1061 ...

The Fisher 377 guard valve assists in maintaining routine process operations that require a specific valve or actuator. When the compressed air pressure drops below the trigger point, the guard valve prevents the actuator from rising, locking in the previous position, or not descending. When the compressed air pressure rises above the trigger point, 3 ...

Description: Fisher/Fisher TBX steam control valves reduce the pressure and temperature of steam to keep power plants running every day. In addition, it protects reheater tubes, condensers, and pipes from excessive pressure, temperature, and enthalpy excursions during steam turbine trips. 　　Products...

It is suitable for steam turbine drainage and steam exhaust applications. peculiarity Forged body. Bonnet/body integrated design. Tungsten-chromium-cobalt alloy Stellite seat. Pilot valve plate. Dustproof casing on the upper part of the actuator. Easy conversion to actuators. Valve position indicator is available Small driving force. ...

Fisher's Model EZR Pilot Operated Pressure Relief Valve or Back Pressure Regulator is commonly used as an overpressure protection relief valve in city gate and district stations, or as a back pressure regulator in commercial and industrial applications. Its quiet and smooth operation, tight shut-off and long service life, even in dirty conditions...

Y602 Series ventilation assemblies help prevent vent obstruction and ensure proper air or gas flow in regulator spring housings, remote ventilation ducts, actuator membrane housings, and other applications. These ventilation components are available in angled or straight-through versions. In general, angular ventilation components protect the side ...

The Fisher Model 585C actuator is typically equipped with a DVC6200 digital valve controller or a 360OP/P or I/P analog positioner. Can be used with a top-mounted or side-mounted manual handwheel (depending on the size of the actuator). Features: Produces up to 111 kN (25,000 lb ...

Fisher easy-e ED control valves are available with straight-through valve bodies, which can be used for regulation or on-off control of a wide range of liquids and gases. With a balanced plug design, cage guidance, and metal-to-metal sealed seat, the Fisher easy-e straight-through valve lets your fluids ...

The Fisher 4660 pneumatic pilot-operated pressure controller activates a safe shutdown system for flowlines, production vessels, and compressors. The pilot is available in single or dual setpoint capability models that use a switching point to maintain full output pressure when the process pressure is within the set point range. If the process ...

Flexible module design – The 3582 Series units can be upgraded to the Model 3582i Electro-Pneumatic Positioner in the field to replace the measurement module with the Model 582i Electro-Ptic Converter Assembly (1). The Type 582i electric-gas converter is attached to the housing of the positioner and provides a very economical ...

Introduction: Model 630R is a general purpose pressure relief valve available in NPS 1 and 2 / DN 25 and 50 body sizes for compressor stations, refineries and similar plants requiring back pressure gas regulation settings up to 250psi/7.2bar. A variety of high and low voltage structures are available. Low-voltage equipment ...

The Fisher Model H120 direct-acting pressure relief valve comes with a pre-installed fixed spring retaining ring. The inlet pressure taker is mounted directly to the spring load lift assembly with a nitrile rubber (NBR) disc. When the inlet pressure exceeds the spring set value, the lifting assembly and disc assembly will be pushed ...

F1 ELDVUEDVC6000 Series Digital Valve Controller (Fig. 1) and Actuator. The digital valve controller receives the valve stroke position in Figure 2) is a communicative, microprocessor-based conversion of electrical signals into feedback, as well as air supply pressure and pneumatic pressure of the actuator. This makes ...

Introduction: The Fisher/Fisher D4 Control Valve is a compact, rugged straight-through valve designed primarily for high-pressure throttling applications, with pneumatic or electric control. This valve is best suited for pressure and flow control applications in the oil and gas production industry. These valves are particularly suitable for ...

The performance and simplicity of the Fisher FIELDVUE DVC2000 meter allows you to operate closer to the set point, improving product quality with more accurate control. WITH FIELDVUE PERFORMANCE DIAGNOSTICS, VALVE OPERATION WILL BE MONITORED ONLINE 24/7 TO ASSESS PERFORMANCE AND RELIABILITY.

Introduction: The Fisher/Fisher Vee-Ball™ V150S flanged control valve has a hemispherical construction and is equipped with a specially designed corrugated V-notch. The Vee-Ball Control Valve combines the ruggedness of a linear valve with the high efficiency of a rotary valve.

The Fisher Series 289 Pressure Relief Valve is a spring-loaded, throttled pressure relief valve that can be used as a downstream pressure regulator to prevent overpressure in the system. Smooth throttling during pressure relief operation minimizes pressure shocks in the system. The Series 289 Pressure Relief Valve is ideal for low pressure settings.

Versatility of application - 5 models and 11 sizes of actuators are available for a wide range of applications. A wide range of spring rates, stroke limiters, and manual operators are available for use in virtually any control valve application. There is an excellent linear relationship between the loading pressure and the stroke.