Weiluntong touch screen can not be turned on, fault analysis and maintenance steps

1. Can the human-machine interface be connected to the PLC? That's not true. Human-computer interface products are produced to solve the human-computer interaction problem of PLC, but with the development of computer technology and digital circuit technology, many industrial control equipment have serial communication capabilities, so as long as there is ...

The new cMT-iV6 is a touchscreen with a built-in cMT Viewer that can be connected and monitored to multiple cMT-SVRs or cMT series machines at the same time. The cMT-iV6 is equipped with a 9.7-inch screen with a resolution of 1024×768, a built-in speaker and a high-performance 1GHz processor.

Ambient light factor, infrared receiver tube has a working range between minimum sensitivity and maximum illumination, but touch screen products can not limit the range of use, from the dark cabaret room to the outdoor use under the high-intensity sunlight on Hainan Island, as a product, it must adapt. Rapid detection ...

1. DIP switch mode touch calibration and system initialization. For the full eMT series, MT8000i series, TK series, WT series and other HMIs, there is a set of reset buttons and DIP switches, which can trigger the corresponding functions when switching between different modes. If the HMI touches ...

Virtual serial port configuration process: 1. Open the virtual serial port configuration software and create two pairs of serial ports; 2. The circle is the physical serial port in the computer, and the virtual serial port in the box; 3. Two groups have been added, and friends who want to add port tests can do so in the window on the right.

1. If you are using a capacitive touch screen, then it is recommended that you first install the driver required for the capacitive touch screen correctly according to the requirements of the manual when you use it for the first time, and then click "Start"/"Program"/"Microtouch Touc" on the screen with your fingers.

Due to the technical limitations and different equipment environment, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the touch screen also needs regular maintenance like ordinary machines, and because the touch screen is a touch all-in-one machine with a high degree of integration of a variety of electrical equipment, so in ...

1. The touch all-in-one machine can carry out the dynamic display of the three-dimensional model of the object, and has a good interactive experience function. The audience can operate by themselves through the touch all-in-one machine, and "touch" the object at zero distance on the screen, and the audience can also rotate and zoom in arbitrarily on the touch all-in-one screen.

1. Plug in the U disk on the touch screen, you don't need to power off the screen, the screen supports the hot-swap function, but at this time, it is best not to communicate with external devices to reduce unnecessary impact. When the screen detects an external device, a dialog box will pop up, select the second Upload Project option ...

4. Use Fault 4.1 What should I do if the newly purchased touch screen downloads the programmed program and it cannot be touched or the touch freezes? First of all, hit the No. 2 DIP switch on the back of the screen to the direction of on, and then power on to see the copyright of the last line of the screen.

1. The infrared touch screen does not need touch pressure, it can be operated freely even if you wear gloves, and anything can be touched. 2. Compared with the display equipped with capacitive and resistive touch screen, the picture saturation is richer and the contrast ratio is better, which improves the user's visual comfort. ...

When the HMI communication failure is caused by on-site interference, the following methods can be used to troubleshoot the fault: The communication line adopts shielded twisted pair cable, and the shielding layer needs to be grounded at one end, that is, only one end of the PLC and the touch screen can connect the shielding layer to the ground horn (it is recommended to connect it to the HMI end of the touch screen) ...

1. Press the "Menu" button to enter the menu interface. 2. Select the "Picture" option to enter the screen settings interface. 3. In the screen settings interface, find the "Copy" option and press the "Enter" key to enter. 4. In the "Copy" option, select "Copy...

(1) FILM - that is, the film used for touch, the base material is PET. When touched, the ITO of the upper and lower layers is brought into contact by deforming the film, resulting in different "resistance values" in the X and Y axes (similar to the principle of moving rheostats). Depending on the requirements of use, the table of FILM ...

1. The touch screen controls the inverter through PLC 1. At present, the general control inverter needs to use PLC to communicate with the inverter, read the information of the inverter, and then the touch screen communicates with the PLC to complete the control of the inverter to start and stop, and monitor the operation of the inverter.

1. High stability, not affected by time and environmental changes 2. Strong adaptability, not subject to current, voltage and static interference, suitable for some harsh environmental conditions (explosion-proof, dust-proof) 3. High light transmittance, no intermediate medium, up to 100% 4. Screen and ...

1. The film surface of the touch screen is the touch surface, that is, the front of the product; The glass side is non-touch, i.e. the back of the product 2. The touch screen part is a glass product, the corners of the glass are sharp, please wear gloves/finger sleeves when assembling 3. The touch screen part is a fragile glass product, and it should not be touched during assembly.

The default standby time is 1 minute. The specific steps are as follows: 1. First of all, open our touch screen editing software, and be sure to select the software corresponding to the touch screen model. 2. Edit the touch screen screen we need. 3. Open the common menu in the upper left corner ...

Open the created Weilun touch screen project, select [Common] in the menu bar and click Open. In the Common drop-down menu, select the Bit Status Indicator icon and click Open. In the pop-up [New Bit Status Indicator] setting window [General Properties] ...

Weiluntong touch screen, also known as "touch screen", "touch panel", is a kind of inductive liquid crystal display device that can receive input signals such as contacts, when touching the graphic buttons on the screen, the haptic feedback system on the screen can drive various connection devices according to the pre-programmed program, which can be ...