Weiluntong touch screen with U disk upload steps

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...

MT(iE) Series (High Performance) 1、MT8102iE 10.1" TFT display 1024*600 dots, brightness 350, contrast ratio 500:1, 16.7M color, 128MB memory, DC19.2-28.8VDC power supply, four-wire resistive, Ethernet Interface/USB Host...

Check whether the connection interface is loose, and then check whether Serial Port and Interrupt Number conflict. If there is a conflict, adjust the resources to avoid the conflict. Then check the surface of the touch screen for cracks. If there is a crack, replace it in time. It is also necessary to check the touch screen table ...

Question 1, How to solve the problem of double click is not sensitive? Open the infrared touch screen to adjust the sensitivity of the program and reduce the sensitivity. Question 2, Is there any drift phenomenon in the infrared screen? The structure of the infrared touch screen is generated by infrared rays, so usually the sleeves and so on touch the infrared screen ...

30. Button control indicator (same address) Set the multi-state transfer switch element/bit state transfer switch element and the multi-state indicator element/bit status indicator element to the same address, click the multi-state transfer switch element/bit state transfer switch element, and the corresponding indicator ...

Precautions when using Verun Tong inverter 　　When shipping and storage During the storage period, it is necessary to ensure that the inverter is not subjected to physical shocks and oscillations. It is also necessary to ensure that they are not exposed to rain and are not placed in places where the ambient temperature is too high. When transferring, hold the bottom of the body ...

1.1 How to delete the job button on the taskbar of the touch screen? Set "Modify/Set System Parameters/General/Job Buttons/Features" to "Closed". 1.2 What does RS485 Default/RS485 2W/RS485 4W Separation mean in the communication port type? r ...

1. The power cord is not properly connected This may seem obvious, but make sure the power cord is connected to the back of the touchscreen and plugged into a power outlet. If it looks like it's connected correctly, disconnect and reconnect both ends of the power cord to make sure the cable isn't loose. 2. The power cord is damaged ...

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

25. Bit status switch switch, bit status indicator, equipment linkage: Through the bit state switching switch element OFF->ON, the macro command is executed: the bit status indicator is set to the ON state; Select the execution macro through the PLC control, select the trigger mode ON->OFF, and set the bit ...

[Fault Analysis and Processing] First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the touch ...

1. If the user is using a capacitive touch screen, it is recommended that the user first install the driver required for the capacitive touch screen correctly according to the requirements of the relevant manual, and then click "Start"/"Program"/"Micro ...

(1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when correcting the position. Solution 1: Recalibrate the position. Phenomenon...

Open the created Weilun touch screen project, select [Common] in the menu bar and click Open. In the Common drop-down menu, select the Bit Status Indicator icon and click Open. In the pop-up [New Bit Status Indicator] setting window [General Properties] ...

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

1. Software editing-system parameter setting-HMI attributes-port number: 8000 change, such as 9000; 2. Bring up the computer task manager - end com_e30.exe under the process; 3. Restart the computer; 4. Query other occupancy on the computer through TCPview software.

1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4W represents the wiring method, that is, the four-wire ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. There are generally three ways to enter the system setting of the TK6070ih touch screen: 1,Generally in the lower right corner of the touch screen, ...

1. First of all, open the Weiluntong touch screen and enter the application. 2. Secondly, select "Edit" → "Personalization" on the control bar of the window. 3. Finally, set the picture to the bottom layer. ...