Introduction of Xinjie PLC inverter visual system

Model introduction of Xinjie PLC 　　XC series Including XC1 (economy), XC2 (basic), XC3 (standard), XC5 (enhanced), XCM (sport), XCC (high-performance) and their corresponding expansion modules, as well as special analog bodies and other special models. XC series PLC can be ...

1. On the premise of satisfying the production equipment and process requirements, the acceleration or deceleration time should be increased as much as possible, and then the overcurrent generation in the process of acceleration or deceleration can be avoided. 2. Check whether the inverter, motor, and production equipment are well matched, whether the transmission part is sensitive, and whether the material is ...

Communication: (1) Radiation disturbance; (2) Conduction disturbance Anti-disturbing method: Regarding the disturbance signal transmitted by the radiation method, it is mainly weakened by wiring and shielding the radioactive source and the disturbed line. With regard to the disturbance signal transmitted through the line, ...

Problem example 1 On the telegram OC problem, measure the 5, 6, and 7 pins of N1 to be 2V. Pin 7 is not 0V for the alarm reason. 1. The "imaginary short" rule of the amplifier is still established, and the N1 chip is good to judge, but the fault is in the bias circuit. 2. Further analysis, at this moment the differential amplifier has ...

(1) There is no need to adjust the parameters, we can maintain the original parameters (default value) when the inverter leaves the factory. (2) It is the parameter that needs to be set and changed before the trial operation. (3) It is a parameter that is adjusted in the operation of the demand. Frequency converters ...

Control principle: PLC controls the operation of the servo motor by controlling the servo motor. 1. The PLC sends a pulse signal to the servo motor driver, pay attention to the driver. 2. The servo motor drive according to the ...

The MS series of servo motors can be installed in either the horizontal or vertical direction. However, if it is installed incorrectly, or in an unsuitable place, it can shorten the life of the motor or cause unexpected accidents. 　　Storage temperature In the unpowered state ...

The most direct cause of cable problems is the breakdown due to the loss of insulation. First of all, there are: a. Overload operation. Long-term overload operation will increase the temperature of the cable, aging the insulation, resulting in breakdown of insulation and degradation of construction quality. b. Electrical: the construction process of the cable head does not meet the requirements.

Tile programming features The editing and display mode in all Chinese greatly improves the readability of the program; Customizable programming instructions. Not only can the name of the instruction be modified according to the characteristics of the industry, but also the instruction can be added or deleted according to the needs of the equipment; Adopt a procedural editing mode. ...

Inverters are mainly divided into two categories according to the frequency conversion method: communication/DC/communication and communication/communication inverters. AC/DC/AC inverter, also known as direct inverter, refers to the operation, the first 50Hz power frequency communication power is converted into pulsating direct current through the rectifier module unit, ...

(1) The PLC shall be installed in an environment that meets the requirements of the rules. (2) In order to facilitate ventilation and disassembly, a space of more than 80mm should be left around the PLC. (3) PLC should be a vertical device and not a horizontal device, that is, the device universal is the direction in which the words on the unit panel can be read normally, otherwise the PLC ...

As the only domestic brand among the top 10 small PLC shopping malls in China, Xinjie has broken through the core shopping malls dominated by international brands for more than ten years, and the unswerving commitment of the leader Li Xin to independent development can be seen. ...

Confirm the rated power and resistance value of the braking resistor. The rated power of the braking resistor should be determined according to the power and moment of inertia of the motor, and the resistance value should be selected according to the specifications of the VFD. In the VFD's parameter settings, find the parameters related to the braking resistor, such as the braking resistor selection ...

(1) The PLC itself should be grounded according to the specified wiring specifications and grounding conditions, and attention should be paid to prevent the use of common grounding wires with Xinjie servo, and the two should be separated as much as possible when grounding. (2) When the power supply condition ...

The problem of the inverter is not only affected by external factors, but also by internal factors. 1. The inverter parameter setting is unreasonable and countermeasures to make the inverter work normally, in addition to the normal equipment, the parameter setting is also very important, if the parameter is not set properly, it will not be able to ...

1. Operating temperature. The inverter is a high-power electronic component, which is easily affected by the operating temperature, and the product is generally required to be 0-55 °C, but in order to ensure the safety and reliability of the operation, it should be considered to leave room for use, and it is best to control it below 40 °C. In the control box, the inverter ...

What is a frequency converter? Variable frequency drive (VFD) uses inverter technology and microelectronics to change the operating power frequency of the motor to control the power control unit of the communication motor. The inverter is mainly composed of rectifier (from communication to DC), inverter, inverter (from DC ...

Xinjie XDM series PLC, XDM is the sports control PLC in the XD series, now has the following types: XDM-24T4-E/C, XDM-32T4-E/C, XDM-60T4-E/C, XDM-60T10-E/C. The XDM series has the following ...

1. Introduction TP Contact Industrial Graphic Displayer (referred to as contact screen) is a human-machine interface (known as HMI or MMI in foreign countries) that connects humans and machines (mainly PLC), which is known as the face of PLC. It is a generation ...