Part of the configuration process for Yaskawa drives

Create Date: 2024-8-30 12:03:23|Source: YASKAWA/Yaskawa

1. "Restore factory settings": Perform a factory reset after power-on to avoid some previously set parameters in the inverter (of course, if it is a new inverter, this problem does not exist).

2. "Set the motor type": whether the motor is an asynchronous motor or a synchronous motor, of course, it is generally an asynchronous motor, and it is also an asynchronous motor by default.

3. "Set the motor parameters according to the motor nameplate": check the motor nameplate on the motor body.

4. "Jog operation to confirm whether the motor rotation direction is correct": in the process of this operation, you must pay attention to whether the load carried by the motor interferes or collides when the motor is running, and the low-speed operation test can be used in the process of running and starting.

5. "Set the inverter to self-learning mode": Some inverters do not support self-learning mode, and the operating parameters of such inverters need to be set one by one. Of course, most of the inverters on the market support self-learning, which greatly liberates our industrial controllers from complicated parameters.

6. "Start learning to match the motor operation": As with the previous jog operation, you must pay attention to whether the load can run forward and backward. At the same time, it should be noted that in the self-learning mode, the motor will rotate rapidly, so be careful.

7. "After the operation is completed, set the operation command channel": through self-learning, you can quickly set the operating parameters of the inverter. At the same time, it is also necessary to manually set the control command source channel for the inverter to run, such as IO terminals, analog ports, network communication, etc.

Part of the configuration process for Yaskawa drives

More on that

	Yaskawa SGD7S-120A00B202 servo driver alarm fault recovery 1. First, confirm the alarm code. The alarm code is different for each servo drive, so you need to consult the corresponding equipment manual or contact the manufacturer for a specific list of alarm codes. 2. Determine the cause of the fault according to the alarm code. Different alarm codes correspond to different fault types, which can be ...
	Yaskawa servo drive failure causes and maintenance treatment Yaskawa MOTOMAN servo drive fault repair: 1. The motor runs faster in one direction than in the other; (1) Cause of failure: The phase of the brushless motor is wrong. Solution: Detect or detect the correct phase. (2) Cause of failure: In the absence of ...
	Common faults and solutions of Yaskawa servo drives 1. When the oscilloscope checks the current monitoring output of the driver, it is found that it is all noise and cannot be read; Cause of failure: The current monitoring output is not isolated from the AC power supply (transformer). Solution: It can be detected and observed with a DC voltmeter. 2. Motor ...
	Yaskawa A1000 inverter control circuit and ground wire wiring method Second, the wiring of the control circuit The control circuit of the inverter can be roughly divided into two types: analog and digital. 1. The wiring of the terminal of the control circuit should use shielded wire or twisted pair wire, and it must be separately routed from the main circuit and the strong current circuit (including the 200V relay program circuit). ...
	Yaskawa V1000 inverter alarm CPF06 fault maintenance after powering on 1. Fault phenomenon: The fault phenomenon is the alarm CPF06 after power-on, which cannot be reset. Second, the maintenance method: The explanation for the CPF06 fault reported by Yaskawa V1000 inverter is: EEPROM data is abnormal. Generally, it is possible to restart the inverter or perform initialization ( A1-03=2220 ) ...
	Yaskawa inverter maintenance method Yaskawa inverter failure and maintenance method. 　　The switching power supply is damaged. Switching power supply damage is the most common fault in many frequency converters, usually caused by a short circuit in the switching power supply load. The 616G3 uses two switching power supplies, which is somewhat similar to the Fujifilm G5. First of all, the DC bus side 530 volts ...
	MindMotion Technology joined hands with Yaskawa Shougang to appear on the CCTV screen again Recently, after appearing on CCTV news during the Beijing Winter Olympics, MindMotion Technology and Yaskawa Shougang appeared on the CCTV stage again, demonstrating the application achievements of the two sides in jointly building an advanced manufacturing cluster in the field of intelligent manufacturing and enhancing the competitiveness of the industrial chain and supply chain. It was reported in the news that the new ...
	Parameter setting steps of Yaskawa H1000 inverter 1. No-load power-on test of inverter 1. Ground the grounding terminal of the inverter. 2. Connect the power input terminal of the inverter to the power supply through the leakage protection switch. 3. Check whether the factory display of the inverter display window is normal, if it is incorrect, it should be reset, otherwise ...
	There are three control modes of Yaskawa servo motor 1. Torque control mode: The torque control mode is to set the output torque of the motor shaft through the input of the external analog quantity or the assignment of the direct address, which is manifested as 10V corresponding to 5Nm, when the external analog quantity is set to 5V, the output of the motor shaft is 2.5Nm: if the electric ...
	How to deal with the BB flashing of Yaskawa servo drive 1. Check whether the power wiring is in good contact, and if the contact is bad, you need to unplug the power supply and re-wire. 2. Check whether the wiring between the servo drive and the host is in good contact, and if the contact is bad, the wiring needs to be removed and rewired. 3. Check the connection between the main machine and the servo drive.
	What are the applications of Yaskawa inverter? 1. Compressor load Compressors are also widely used loads. Low-pressure compressors are widely used in various industrial sectors, and high-pressure large-capacity compressors are widely used in steel (such as oxygen generators), mines, fertilizers, and ethylene. The use of frequency conversion speed regulation, all bring small starting current, ...
	A brief introduction to Yaskawa teach pendant programming The display of the teach-in programmer is a 5.7-inch color display. The available characters are English letters, numbers, symbols, katakana, hiragana, and kanji. In addition, when entering Japanese, you can also convert it to kana kanji by entering romaji. 　　Rotate [REMOTE] to enter the remote ...
	What is the difference between the origin setting of Yaskawa robot, the location of the second origin, and the location of the origin of the job? What is the difference between the origin setting of Yaskawa robot, the location of the second origin, and the location of the origin of the job? Origin Setting: Lets you set the origin and initial position of each axis. The robot → the origin position → point display, and select the axis and robot you want to set 1. Write origin data → point ...
	Analysis of fault codes of Yaskawa inverter Analysis of the fault code of Yaskawa inverter, for reference only: OC Overcurrent The output current of the inverter exceeds the overcurrent detection value · GF grornd Favlt Grounding The ground current on the output side of the inverter exceeds 50% of the rated output current of the inverter ...
	Yaskawa Robot was launched in China to create a mutually beneficial and win-win pattern China's industrial manipulator (15.620, 0.00, 0.00%) market capacity continues to develop, and overseas robot manufacturers have surged production capacity to solve China's requirements. As one of the "four families" of intelligent robots, Yaskawa Electric has accelerated the rational layout of Chinese artificial intelligent sales market, ...
	Yaskawa Robotics - Classification and introduction of industrial robot drive systems 1. Hydraulic drive system Because hydraulic technology is a relatively mature technology. It has the characteristics of large power, large force (or moment) to inertia ratio, fast response and high response, and easy to realize direct drive. It is suitable for working in large load-bearing capacity, large inertia and solder-mask environments.
	Yaskawa servo drive failure and repair 1. The motor runs faster in one direction than in the other; (1) Cause of failure: The phase of the brushless motor is wrong. Solution: Detect or detect the correct phase. (2) Cause of failure: When not used for testing, the test/deviation switch hits the test position. ...
	Yaskawa Servo Drive FAQ (10-18) [10] Yaskawa servo back to the origin can not find the C phase pulse, Yaskawa servo drive and motor, using the travel switch + C phase back to zero mode, now the pressure on the switch deceleration can not find the C phase pulse, servo motor, drive, host computer, which fault is the most likely? A: Servo motor rotation ...
	Yaskawa Servo Alarm C90 (AC9) Alarm Cause Analysis and Solution 1. Analysis of the causes of Yaskawa servo alarm C90 (AC9): 1. The encoder cable is broken or the encoder plug is made in poor process (there are also wiring errors in the alarm of the new machine); 2. The servo drive itself is faulty; 3. Environmental interference, caused by poor connection: ...
	Types and applications of Yaskawa's high-temperature resistant robot protective clothing Yaskawa robot is a kind of industrial robot, which can be applied to various automated production lines according to its specifications and models, and the high-temperature work workshop is a major field where industrial robots are used more, so it needs to be protected by robot protective clothing. The following is a brief introduction to Ontor ...