Sick new products on the market | Medium and long range photoelectric sensor G20 series

The miniaturization, integration, and intelligence of sensors are the main trends of industrial development, and the increasing demand for small and integrated smart chips in industrial scenarios also provides better means for equipment integration and intelligence. Sick is also deeply aware of the small size of the large ...

1. Self-regulation. At the beginning of use, please check whether the switch itself is defective and whether the appearance is defective. 2. When avoiding obstructions. When the photoelectric switch is used, for some goods such as colored goods, goods with weak reflectivity, and goods with large gaps between small pieces...

The load cell is a relatively easy to damage component in the weighing cell, and it is easy to cause damage to the sensor due to impact, overload, aging, high temperature, corrosion, etc. (1) Physical observation: observe whether the appearance of the load cell is deformed, cracked, etc. (2) Measure the resistance ...

The color and number of SICK sensor wires are conveniently different. Some are six-wire sensors. However, the two sense lines are also connected to the sensor's book input signals E+ and E-, and we can ignore these two feedback lines or combine them into one. The color of each cable ...

What are the applications of color sensors? 1. Discrete photodiode with color filter The traditional way to sense color is to use a structure that combines three to four photodiodes on a single chip, with red, green, and blue color filters placed on the surface of the photodiodes. Independent...

SICK Germany has been ranked 2nd in the list of "Best Employers in Germany 2022"! For 20 years in a row, SICK has been on the list of "Best Employers in Germany"! The list is published by the Great Place to Work Institute®, the world's leading ...

Proximity sensors are divided according to their working principle: High-frequency oscillation type, capacitive type, induction bridge type, permanent magnet type, Hall effect type, etc. According to the principle of operation, it can be divided into three categories: High-frequency oscillation type using electromagnetic induction, magnetic force type using magnets, and ...

Resistance, inductance and capacitance are the three major types of passive components in electronic technology, and a capacitive sensor is a sensor that converts the measured change into a capacitance change, which is essentially a capacitor with variable parameters. Capacitive sensors offer the following advantages: (1) ...

(1) High measurement accuracy; The reason why RTD sensors have high measurement accuracy is mainly because the resistance temperature characteristics of some materials are stable and reproducible. Secondly, compared to thermocouples, it does not have the problem of reference end error; (2) It has a large measurement range, especially in low temperatures; ...

1. Detect the torque in the working process of various machining centers and automatic machine tools. 2. Detect the load torque and input power of reducer, fan, pump, mixer, winch, propeller, drilling machinery and other equipment. 3. Detection of generators, electric motors, internal combustion engines...

1. Alarm code E401 E401 is one of the common fault codes of fiber optic sensors, which indicates that the fiber optic sensor has detected that the fiber is cracked or bent. This problem can usually be dealt with by replacing the fiber or adjusting the fiber installation orientation. 2. Alarm code E402 ...

1. First, connect the external hardware and install the external COM port of the scanner to the serial port of the industrial computer. 2. The power supply of the SICK scanner control box is 24V positive and negative induction eyes, and the feedback signals of 10, 11 and 12 corresponding to the electric eyes, 24V+, 24V-. ...

In the electronics industry, optimizing products and processes is at the heart of the smart solutions of the future. The end product will be smaller, flatter and lighter, expanding its performance in a completely new size. The more streamlined the automation solutions are, the more they can make the most of their quality and cost savings.

1. The pressure goes up, the output of the transmitter does not go up to this situation, you should first check whether the pressure interface is leaking or blocked, if you admit that it is not, check the wiring method and check the power supply, if the power supply is normal, then simply pressurize to see if the output changes, maybe observe whether the zero position of the sensor has an output, if there is no ...

1. Two-wire system: the way to connect a wire at both ends of the thermal resistance to draw out the resistance signal is called the two-wire system: this lead method is very simple, but because there must be a lead resistance r for connecting the wire, the size of R is related to the material and length of the wire, so this lead method is only applicable to ...

In the application of inductive proximity sensors, customers are often trapped by the lack of space to install, and the small parts are too small to be effectively detected, and the IMM miniature proximity sensor provides a variety of application solutions in this type of application. IMM miniature proximity sensor with a richer ...

In the current era of rapid economic development, logistics is known as the "blood" of the national economy, although the early Chinese logistics industry started late, with the continuous improvement of the system, the rapid development of high and new technology, now the logistics industry has become a social and economic bridge and link. Among them, the data flow is ...

1. Laser length measurement Precision length measurement is one of the key technologies in the precision machinery manufacturing industry and the optical processing industry. Modern length measurement is mostly carried out by using the interference phenomenon of light waves, and its accuracy mainly depends on the monochromacy of light. Laser is the most ideal light source, it is more ...

1. At present, SICK pressure sensors can be used in combination with computers and instruments to improve operation and reduce errors. The human-machine dialogue function is the main feature of SICK pressure sensors, and the display device and input keyboard equipped with it become the medium for human-machine dialogue. 2. SICK pressure sensing ...

Dynamic features: The so-called dynamic characteristics of the sensor refer to the characteristics of the output of the sensor when the input changes. In practice, the dynamic characteristics of a sensor are often expressed in terms of its response to some standard input signal. This is because the sensor's response to a standard input signal ...