How to adjust Rexroth A11V hydraulic pump?

1. Guiding ideology: 1. The pressure depends on the load oil pump, and the output pressure is inversely proportional to the flow rate. In the state of electronic control, when the external load increases, the system pressure increases, when the system pressure increases, the pressure of the front pump oil flow and the rear pump oil flow into the rear pump increases, and the computer detects the ...

1. Water will corrode the oil pump, so it is forbidden to use the oil pump to vacuum the substance containing water. 2. For substances containing a large amount of solvent, remove most of the solvent in the oven first, and then use an oil pump to vacuum. 3. Use the vacuum pump in the correct order to prevent suck-back. ...

1. The bearing of the hydraulic motor can withstand the radial force, and the transmission parts such as the pulley shall not be directly installed on the spindle for the motor that cannot withstand the radial force. The driving sprocket is driven by a hydraulic motor, and the driven sprocket drives the conveyor belt roller. According to the user's report, the motor often leaks...

1. Guiding ideology: 1. The pressure depends on the load oil pump, and the output pressure is inversely proportional to the flow rate. In the state of electronic control, when the external load increases, the system pressure increases, when the system pressure increases, the pressure of the front pump oil flow and the rear pump oil flow into the rear pump increases, and the computer detects the ...

1. What should I pay attention to when using a gear pump? (1) The oil suction height of the gear pump shall generally not be greater than 500mm. (2) The gear pump should be directly connected with the motor through the flexible coupling, generally not rigidly connected or connected with the power source through the gear pair and belt mechanism, so as to avoid unilateral force, ...

1. Hydraulic pump: Straight shaft swash plate piston pumps are divided into two types: pressure oil supply type and self-priming oil type. Most of the pressure oil supply hydraulic pumps use oil tanks with air pressure, and there are also hydraulic pumps with oil replenishment sub-pumps to provide pressure oil to the oil inlet of the hydraulic pump. The self-priming oil energy of the self-priming hydraulic pump ...

1. Check the internal leakage of the boom cylinder. The easiest way to do this is to raise the boom and see if it has a noticeable free descent. If the drop is obvious, disassemble the cylinder for inspection, and replace the sealing ring if it is worn; 2. Check the control valve. First of all, clean the safety valve and check whether the valve core is grinding.

Hydraulic pumps can be divided into four types according to their working principle, the details are as follows. 1. Gear pump The volume is smaller, the structure is simpler, the cleanliness of the oil is not strict, and the price is cheaper; However, the pump shaft is subject to unbalanced force, severe wear and tear, and large leakage. 
Externally meshing gear pump when tooth ...

1. The installation of the piston pump needs special attention, the direction should not be mistaken, and the direction of the oil filler port should be upward, so that it is more convenient to use in the later stage. And it is necessary to use flexible couplings, which can better avoid any stress generated during the bending process, but the axial error needs to be 0 ...

1. It plays the role of pressure stabilization and overflow (the valve port is normally open) In the fixed pump oil inlet or return oil throttling speed control system 2. Safety protection function (valve port normally closed) Variable pump hydraulic system, fixed pump bypass throttling speed regulation system and non-throttling speed regulation system. 3. The effect of anti-load 4、 ...

An automation platform with an ecosystem can perform a wide range of tasks Provide low-code engineering and applications for bot applications Web-based HMIs and consumer device applications are possible One device for multiple tasks: security, data analysis ...

1. Poor assembly of Rexroth hydraulic pump leads to abnormal heating of the hydraulic pump 1. The courtyard of Litule hydraulic pump is not suitable, (for example, the plunger and cylinder, blade and rotor groove, sperm and rotor, gear, side plate, etc. are too small, and the sliding part may be overheated.) 2. The installation of Rexroth hydraulic pump ...

Bosch Rexroth Co., Ltd. ("Bosch Rexroth") and Wuxi Weifu High-Tech Group Co., Ltd. ("Weifu Group"), located in Wuxi, Jiangsu Province, China, plan to cooperate to establish a joint venture that aims to combine the strengths of both companies and create a joint venture for ...

peculiarity 1. Rexroth solenoid valve, solenoid valve and all stainless steel; For highly corrosive media, the diaphragm type must be selected. Neutral medium, it is also advisable to choose a solenoid valve with copper alloy as the housing material, otherwise, rust chips often fall off in the valve housing, especially when the action is infrequent. Ammonia valves ...

1) The pressure and speed can be adjusted infinitely, and the impact phenomenon of the constant on/off valve is avoided. 2) It can realize remote control and program control. 3) Compared with intermittent control, the system is simplified and the components are greatly reduced. 4) Compared with hydraulic proportional valves ...

1. Pressure reducing and stabilizing valve Main features: 1. Piston type with DN65 caliber or above. The life of the diaphragm is increased by more than 3 times; 2. Below DN50 caliber, the original diaphragm is replaced by a flat diaphragm of nylon reinforced rubber, which also improves the service life by more than 3 times. Applicable medium: water, air. Medium temperature ...

The combination of Bosch Rexroth and Hydfoss contributes to the expansion of the hydraulic portfolio worldwide Join forces to open up new market opportunities and expand sales channels Bosch Rexroth AG (hereinafter referred to as "Bosch Rexroth") plans to acquire a company located in Iraq, United States.

Want to carry out moving tasks with ease? Let the Bosch Rexroth Smart Handling Function Kit help you. Thoughtfully conceived and easy to set up, this mechatronic kit significantly reduces the time required to design handling solutions and takes your productivity to a whole new level. Why...

1. Daily maintenance 1) Strictly implement the post operation method and carefully fill in the operation records. 2) Check the bearing temperature and oil pressure regularly; Check the level height of the lubricating oil every shift. 3) Check whether there is leakage in the sealing part once per shift. 4) Do a good job in each shift ...

First, the rigidity of the hydraulic oil decreases sharply, resulting in the slower response of the hydraulic system and the reduction of efficiency, resulting in crawling and vibration of the actuator. Second, air bubbles will cause oil film to be unable to form between moving parts, resulting in poor lubrication and aggravating the wear of hydraulic components. The third is in the air ...