1. Guiding ideology:
1. The pressure depends on the load oil pump, and the output pressure is inversely proportional to the flow rate. In the state of electronic control, when the external load increases, the system pressure increases, when the system pressure increases, the pressure of the front pump oil flow and the rear pump oil flow into the rear pump increases, and the pilot secondary pressure of the electro-proportional valve outlet is also greater by the computer detection relevant signal, the former acts on the primary piston, the latter acts on the secondary piston, and the two push the piston to overcome the spring force to move to the left, and the piston pushes the spool of the spool to the left to overcome the spring force of the spool to move to the left, so that the spool of the spool is in the left position.
2. At this time, the oil flow of the rear AY oil pump can act on the large end of the variable piston through the left position of the spool of the spool of the slide valve, where the oil passage changes from normally closed to normally open, because the cross-sectional area of the two ends of the piston is unequal, the pressure acting on the large end of the variable piston of the swash plate is greater than the pressure at the small end of the variable piston plunger, and the plunger moves to the left.
3. At the same time, the position change of the swash plate and the spool valve sleeve: the swing angle of the swash plate gradually decreases, which reduces the displacement of the oil pump, and the sliding sleeve of the spool valve moves to the left at the same time, and gradually cuts off the oil passage communicated between the variable piston cavity and the oil flow of the rear pump, when the oil port is completely cut off, the swash plate is stationary, the swash plate no longer swings, the oil pump completes the variable, and the flow output is stable.
2. When the external load becomes smaller, the system pressure becomes smaller, the three oil flow pressures acting on the first and second stage pistons become smaller, the balance between the oil flow pressure and the spring force is broken, the spring is gradually pushed back, and the spool of the spool is gradually pushed back to the right, so that the large cavity oil channel of the inclined plate piston is communicated with the oil drain port, and the pressure of the large cavity of the variable piston begins to be reduced.
3. At the same time, the swash plate and the spool valve sleeve are changed: the angle of the swash plate gradually increases, and the displacement of the oil pump is increased; At the same time, the sliding sleeve of the slide valve moves to the right, and gradually closes the oil channel between the large cavity of the swash plate and the oil drain port, when the spring force and the oil flow pressure form a new balance and the oil channel between the piston cavity and the oil drain port is completely cut off, the plunger no longer moves, the swash plate no longer swings, the oil pump completes the variable, and the flow output is stable. When the external load changes, the balance between the oil flow pressure and the spring force is broken again, and the displacement also changes, and the two always change with the change of load, in a dynamic balance.
Fourth, the electronic control state: the control hydraulic signal related to the displacement change is the oil flow of the front pump, the oil flow of the rear pump and the pilot oil and negative flow, in which the oil flow of the front and rear pumps directly controls the oil pump, and the pilot oil controls the oil pump after throttling through the electric proportional valve, which we can call the pilot secondary pressure. Let's take the control of the pump as an example to analyze the change in displacement.
|
More on that
|
Analysis of the reasons for the insufficient flow of Rexroth hydraulic pump plunger pump
(1) Insufficient inhalation
The reason is that the resistance in the suction line of the Rexroth piston pump is too high or the oil replenishment is insufficient. For example, the speed of the pump is too large, the liquid level in the oil tank is too low, the oil inlet pipe is leaking, and the oil filter is blocked.
(2) The amount of leakage is too large
The reason is the gap in the Rexroth piston pump ...
|
|
Rexroth hydraulic pumps – precautions for the use of proportional valves
1. The power domain (working limit) of the proportional valve
For direct-acting electro-hydraulic proportional throttle valves, since the hydraulic force acting on the valve core is proportional to the flow rate and flow rate (pressure) through the valve port, when the working condition of the electro-hydraulic proportional throttle valve exceeds the product of its pressure drop and flow rate, that is, the power meter...
|
|
The solution to the forward rush of the throttle speed control valve of Rexroth vane pump
1. Adopt the correct Rexroth vane pump speed conversion method, the conversion mode of the solenoid valve, the impact is larger, the conversion accuracy is lower, the reliability is poor, but the control flexibility is large;
2. The electro-hydraulic reversing valve uses a current valve with damping, and by adjusting the damping size, the Rexroth blades ...
|
|
Rexroth Hydraulic Pumps – Routine maintenance and troubleshooting of gear pumps
1. Daily maintenance
1) Strictly implement the post operation method and carefully fill in the operation records.
2) Check the bearing temperature and oil pressure regularly; Check the level height of the lubricating oil every shift.
3) Check whether there is leakage in the sealing part once per shift.
4) Do a good job in each shift ...
|
|
What are the differences between Rexroth proportional valves and Rexroth servo valves?
First of all, there are no strict regulations and explanations for the difference between Rexroth proportional valves and Rexroth servo valves, which is the main reason why most people do not understand the difference between the two.
|
|
Introduction to the classification of Rexroth relief valves
(1) Rexroth DBD direct acting relief valve: DBD valve is a direct-acting relief valve, which is used to limit the system pressure, with a total of 7 pressure levels: 2.5, 5, 10, 20, 31.5, 5, 40 and 63Mpa. The types of pressure adjustment are: adjustment handle, adjustment handle with lock, and adjustment screw with protective cover.
|
|
Bosch Rexroth generated sales of 7 billion euros, a record for the company's history
Despite the challenging environment, Bosch Rexroth achieved double-digit sales growth in fiscal 2022;
Demand for new orders remained strong at 7.3 billion euros;
Record investments in R&D, innovation and production networks;
Through acquisitions and mergers ...
|
|
Rexroth balance valve balancing principle and its function description
The balancing principle of the balancing valve and its function are explained
The principle of balance
The TA balancing concept is the concept of total equilibrium, which believes that only after the resistance of the system is adjusted and balanced, can each equipment obtain the design flow under the design operating conditions.
Fluid network system for the HVAC industry
...
|
|
Introduction to the basic features of Rexroth piston pumps
Volumetric efficiency (actual discharge/theoretical discharge) rotates at low speed, and internal leakage increases when used at high pressure, and efficiency decreases.
Solid shaft dynamics (theoretical shaft dynamics/mechanical efficiency): number of rotations, increased pressure, increased mechanical efficiency.
Real discharge (volumetric efficiency), real axis power and number of rotations ...
|
|
Rexroth launches the new linear module SMS
● Five pre-configured sizes: 30-120 mm
● Optional compact motor accessories
● Order online and deliver in stock
The new linear axes are suitable for handling cost-sensitive small parts and can be used as an alternative to complex pneumatic solutions. (Image source: Bosch Rexroth Co., Ltd.)
|
|
Bosch Rexroth: Smart handling for the factory of the future
It's hard to imagine a factory automation system without linear robots. The application of linear robots involves handling incoming materials during product production, assembly or packaging, whether integrated into a single machine as a pick-and-place unit or integrated into a semi-automatic or fully automated production line. However...
|
|
Rexroth Hydraulic Pumps - Introduction to the mechanical classification of piston pumps
Piston pumps are generally divided into single piston pumps, horizontal piston pumps, axial piston pumps and radial piston pumps.
Single piston pump
The structure consists of an eccentric wheel, a plunger, a spring, a cylinder block, and two check valves. A closed volume is formed between the plunger and the cylinder bore. The eccentric wheel rotates and the column ...
|
|
Rexroth hydraulic oil pump disassembly process
1. Loosen and remove the connecting screws on the pump cover and bearing end cover.
2. Remove the positioning pin, pump cover and bearing cover.
3. Take out the transmission shaft and shaft sleeve from the housing of the pump.
4. Take out the two gears from the casing of the pump.
5. Remove the floating side plate and sealing ring ...
|
|
How to adjust the pressure and displacement of the hydraulic piston pump?
1. Adjust the displacement of the pump: The larger the displacement of the hydraulic piston pump, the greater the flow and pressure. The displacement can be adjusted by replacing the displacement of the pump or adjusting the eccentricity distance of the pump.
2. Adjust the valves in the hydraulic system: The valves in the hydraulic system can control the flow and pressure.
|
|
What are the functions of Rexroth relief valves?
1. It plays the role of pressure stabilization and overflow (the valve port is normally open)
In the fixed pump oil inlet or return oil throttling speed control system
2. Safety protection function (valve port normally closed)
Variable pump hydraulic system, fixed pump bypass throttling speed regulation system and non-throttling speed regulation system.
3. The effect of anti-load
4、 ...
|
|
Disassembly and cleaning steps for Rexroth hydraulic valves
(1) Disassembly. For hydraulic valves, although most of the parts are connected by bolts, the hydraulic valve is not disassembled when designed, and if it is forcibly disassembled due to lack of special equipment or lack of professional technology, it may lead to damage to the hydraulic valve. ...
|
|
Rexroth hydraulic pumps – use, repair and assembly of gear pumps
1. What should I pay attention to when using a gear pump?
(1) The oil suction height of the gear pump shall generally not be greater than 500mm.
(2) The gear pump should be directly connected with the motor through the flexible coupling, generally not rigidly connected or connected with the power source through the gear pair and belt mechanism, so as to avoid unilateral force, ...
|
|
What to do when air enters the Rexroth hydraulic pump motor?
When Rexroth hydraulic pump motor has air, how do we correctly eliminate it so that the pump is not damaged, and then share with you the correct exhaust method:
(1) The oil has a certain compressibility, resulting in noise, vibration and crawling of moving parts in the system.
|
|
Where does the daily maintenance of Rexroth hydraulic pump start?
1. Maintain a proper oil temperature
The working temperature of the hydraulic system is generally controlled between 30 and 80 °C (dangerous temperature ≥ 100 °C). Too high oil temperature in the hydraulic system will lead to: the viscosity of the oil will decrease, which will easily cause leakage and reduce efficiency; The strength of the lubricating oil film decreases, accelerating the mechanical ...
|
|
Rexroth at the Hannover Messe 2023
At the Hannover Messe 2023, Bosch Rexroth presented several open, easy-to-integrate automation solutions and will continue to drive the digital transformation of mechanical engineering. In the field of hydraulics, Bosch Rexroth is transferring more functions to the software. The solution adopts the ...
|
|
Contact
working hours
