and Lisi PLC - the difference between PLC and inverter

1. Check before power-on If the cable insulation resistance meets the requirements (greater than 5M ohms), check the cable insulation resistance test record, and spot check the actual measurement if necessary. Check that all power cables, signal cables, and communication buses should be connected. Control stations, operator stations, engineer stations, etc.

1、-10—10V。 When the voltage of -10V-10V is converted to F448-0BB8Hex (-3000-3000) at 6000 resolution; At 12000 resolution, it is converted to E890—1770Hex (-6000—6000). 2、0—10V。 At a voltage of 0-10V, at a resolution of 12000 ...

When the PLC understands the interrupt function, it needs to understand the PLC's operating cycle or scan cycle. It is necessary to talk about the process of PLC sequential control loop execution, which is a prerequisite for understanding interruptions and must be mastered. It is divided into three parts, input processing, program processing, and output processing. 1、 ...

1. Data backup When carrying out maintenance, we must cut off the power, data backup between power outages is an important link, for the data that needs to be archived for a long time, you can back up the historical trend data to the mobile hard disk, and then turn off the Windows-based operating system (Note...

1. The thermocouple uses a compensation wire, and there can be a node in the middle, but the corresponding compensation cable must be used to directly connect to the DCS thermocouple module, such as the LLMUX card in HONEYWELLTPS. Minimize nodes to reduce interference. In addition, in the DCS configuration, it is necessary to select the corresponding thermocouple model, and supplement the ...

1. Use the analog output module of the PLC to control the analog output module of the inverter The analog output module of the PLC outputs a 0-5V voltage signal or a 4-20mA current signal, which is used as the analog input signal of the inverter to control the output frequency of the inverter. This control method is simple to wiring, but it needs to be selected and changed.

Facing China's "double carbon" strategic goals, the Beijing Economic and Technological Development Zone is guiding a large number of enterprises to explore the implementation plan of "carbon peak" and "carbon neutrality", and strive to build a number of green factories, green products and green supply chains. Recently, enterprises in the zone and Lisi Group signed a contract for the first time in China to use CO (dioxide...

1. The switching quantity is also called the logical quantity, which means that there are only two values, 0 or 1, ON or OFF. It is the most commonly used control, and controlling it is the advantage of PLC, and it is also the most basic application of PLC. The purpose of switching control is to follow the current input combination with the historical input according to the switching quantity.

(1) The ambient temperature exceeds the range of 0-50 °C; (2) The relative humidity exceeds 85% or there is dew condensation (caused by sudden temperature changes or other factors); (3) direct sunlight; (4) There are corrosive and flammable gases, such as hydrogen chloride, ...

1. Check the circuit according to the drawing (without power transmission) The drawings of the general PLC system include two parts: the drawings in the cabinet and the drawings outside the cabinet; The drawing in the cabinet refers to the wiring diagram inside the cabinet; The out-of-cabinet drawings are the wiring diagrams of all electrical cabinets that are connected out. This part needs to be checked for; 1. Drawings ...

(1) Computing function The computing functions of a simple PLC include logic operation, timing and counting functions; The operation functions of ordinary PLC also include data shift, comparison and other calculation functions; More complex arithmetic functions include algebraic operations, data transmission, etc.; There are also analog PIDs in large PLCs.

1. Preliminary preparations Engineering configuration is operated at the engineer station, and before engineering configuration, it is necessary to have the necessary tools and information, specifically: Tools: refers to the hardware environment and software environment used in engineering configuration, usually refers to the ...

DCS is the English abbreviation of distributed control system (Distributed Control System), distributed control system is referred to as DCS, which can also be literally translated as "distributed control system" or "distributed computer control system". The decentralized control system is based on the microprocessor, and the control function is decentralized.

1. The output accuracy is as high as 0.05%, which greatly improves the operation efficiency of the system. 2. The full-scale output of the channel signal is 0-22.7mA, and the output range is wide; 3. It can be adapted to the enhanced base to achieve channel resistance to 220VAC; 4. It has a perfect channel signal diagnosis function, which can be realized.

1. PLCZ self-fault judgment In general, PLCs are extremely reliable devices with a very low failure rate. The probability of hardware damage such as the CPU of the PLC or software running errors is almost zero; If the PLC input point is not caused by strong current intrusion, it will hardly be damaged; PLC output relay ...

1. The physical structure of the interface 1. RS232 interface: One of the computer communication interfaces, usually RS-232 interface in 9 pin (DB-9) or 25 pin (DB-25) form, generally there will be two sets of RS-232 interfaces on personal computers, respectively called COM ...

The steps of DCS system troubleshooting include: (1) Check the fault caused by improper use. Common types of operational faults include operator errors, terminal wiring faults, module installation faults, and power supply failures. (2) Troubleshoot the improper operation of the DCS system ...

Hollysys Automation provides automation solutions for many fields. 　　Intelligent TCM solutions In order to make the drug achieve the harmony and unity of the doctor's peace of mind, the pharmacist's formula, and the patient's peace of mind, higher requirements are put forward for the pharmacy environment and hospital management. But...

On December 18, 2020, the "8th Member Congress and 2020 Zhejiang Enterprise Leaders Summit" hosted by Zhejiang Enterprise Confederation, Entrepreneur Association and Industrial Economics Federation (hereinafter referred to as the "Three Associations" of Zhejiang Province) was held in Hangzhou. At the conference, the top 100 in Zhejiang Province in 2020 were commended.

Kunming Changshui International Airport is one of the eight regional hub airports in China and one of the five national large-scale gateway hub airports. With the rapid economic development of Yunnan Province, the aviation business volume of Kunming Airport has grown rapidly.