HollySys PLC - What places should be avoided when installing PLC?

Merit: 1. High reliability: The DCS system has multiple redundancy, backup and recovery mechanisms, which can ensure the high reliability and stability of the system. 2. Sensitivity: The DCS system can be customized according to different industrial processes to meet different control requirements. 3. Efficiency: D...

1. Power off 2. Cleaning the ash can not only clean the surface, but also clean the internal card key of the controller 3. If there is a supporting UPS, open the UPS and clean the ashes 4. After cleaning the ash, check whether the card and relay are loose, and tighten them if they are loose 5. The relays with frequent actions should be cleaned regularly.

1. Logic control of switching quantity This is the most basic and most extensive application field of PLC, which replaces the traditional relay circuit to achieve logic control and sequence control, which can be used for the control of a single device, as well as for multi-machine group control and automatic assembly line. Such as injection molding machines, printing machines, ...

1. PLCZ self-fault judgment In general, PLCs are extremely reliable devices with a very low failure rate. The probability of hardware damage such as the CPU of the PLC or software running errors is almost zero; If the PLC input point is not caused by strong current intrusion, it will hardly be damaged; PLC output relay ...

1. Input of switch command signal The input signal of the inverter includes a switch-type command signal that controls the operating status such as operation/stop, forward/reverse, section speed, and joging. Frequency converters usually make use of relay contacts or components with relay contact switching characteristics (such as crystals).

Fourth, the fundamental sequence of repairing PLC. 1. Start first. 1) When repairing the PLC, do not start directly immediately, but first ask about the situation and the phenomenon of the problem before and after the problem; 2) If you repair an unfamiliar PLC, you should first understand its operating principle. ...

The steps of DCS system troubleshooting include: (1) Check the fault caused by improper use. Common types of operational faults include operator errors, terminal wiring faults, module installation faults, and power supply failures. (2) Troubleshoot the improper operation of the DCS system ...

(1) Select the appropriate PLC model and I/O points, and select the special function module when there are special function requirements. (2) Familiar with the selected PLC programming instructions and compilation software. (3) Carry out soft component planning, including internal relays, holding relays, data registers, ...

From November 15th to 17th, the 2022 China Nuclear Energy High-Quality Development Conference and Shenzhen International Nuclear Energy Industry Innovation Expo (hereinafter referred to as the "2022 Shenzhen Nuclear Expo") will be grandly reopened at the Shenzhen World Convention and Exhibition Center. 　　The theme of this year's Nuclear Expo is "Nuclear Gathering in the Bay Area, Activating the World".

First, the type of failure of the PLC. 1. External equipment failure. External equipment refers to various switches, sensors, actuators, loads, etc., which are directly connected with the PLC operation process. The failure of these equipment will directly affect the control function of the PLC system. Therefore...

1. The connection line is loose and the contact is poor When the run indicator of the PLC turns red, the position of the plug changes to green with a manual move, indicating that the plug is loose, and it is best to replace the new connecting wire, and the plug is frequently plugged and unplugged, which will also lead to poor contact. 2. Strong electrical interference (external)

01 Node bus failure The node bus material is usually a coaxial cable, so as long as there is a cable disconnected, the communication of all devices on the bus will be paralyzed, which will cause serious phenomena such as data loss, equipment stoppage and operation interruption, and may eventually directly or indirectly cause huge ...

In December 2020, the equipment of Sinopec Qingdao Petrochemical Co., Ltd. (hereinafter referred to as Qingdao Petrochemical) 5 million tons/year oil refining integration project, which was upgraded and transformed by Hollysys, was successfully operated, marking the successful completion of the DCS equipment upgrading task. This upgrade is a major development for Sinopec Industrial Holdings.

Recently, the signing ceremony of the strategic cooperation between Bureau Veritas and Hollysys and the functional safety certification ceremony of Hollysys valves were held in the Hangzhou base of Hollysys. Mr. Ye Jiong, General Manager of Bureau Veritas Technology Center, Mr. Zhong Aimin, Director of Product Certification Center, Mr. Yang Yang, Sales Director of Eastern Region, and Mr. Yang Yang, Director of Functional Safety ...

1. High reliability Because DCS disperses the system control function on each computer, and the system structure adopts a fault-tolerant design, the failure of one computer will not lead to the loss of other functions of the system. In addition, due to the fact that the tasks undertaken by the various computers in the system are comparatively ...

DCS is properly blacked out When the DCS needs to be powered off for maintenance due to overhaul or other reasons, we often directly power off the DCS, but sometimes this non-standard operation will bring serious consequences, such as configuration loss, PID parameter loss, etc. So there is a need for blackouts and re-on...

On August 16, 2021, the Tarim Oilfield Natural Gas Ethane Recovery Project, the largest natural gas deep processing base in Xinjiang (1), a key project of PetroChina, was successfully completed and put into operation, with stable operation and the production of qualified ethane products. Tarim Oilfield Natural Gas Ethane Recovery Project ...

In general, DCS control systems require two types of grounding: protective ground and working ground (logical, shielded, etc.). For systems equipped with safety barrier explosion protection measures, such as those used in the chemical industry, intrinsically safe premises are also required. 2.1 Protected areas (CG, Cabinet Grounding...)

(1) High reliability DCS is designed to be fault-tolerant, so that when a computer fails, it does not cause the system to lose other functions. In addition, because the tasks undertaken by the individual computers in the system are relatively simple, it is possible to adopt a specific structure and ...

1. PLC programmable logic controller (programmable controller). 2. DCS system pays more attention to the field of process control. Such as chemical, smelting, pharmaceutical, etc. It mainly monitors and controls some field parameters, while PLC focuses on logic control. machining). Of course, the PLC's ...