Whether it is a linear displacement sensor or a rope displacement sensor, it often encounters a variety of problems when it is used, including quality problems, application problems, environmental problems, etc., but the use of problems is common, and improper use simply makes the sensor damaged. Therefore, we need to pay attention to all aspects when using the sensor to ensure the normal use of the sensor. Today, we will focus on the matters we should pay attention to in the application of linear displacement sensors.
1. The problem of small power supply capacity of linear displacement sensor
The lack of power supply capacity will cause the following conditions: the movement of the melt will change the appearance of the clamping electronic ruler and have fluctuations, or the movement of the clamping will cause the appearance of the injection electronic ruler to fluctuate, resulting in a large measurement error. This situation is easier to present if the driving power supply of the solenoid valve is shared with the power supply of the linear displacement sensor.
2. What are the requirements for the alignment, parallelism and viewpoint of the linear displacement sensor?
The installation of a linear displacement sensor requires a high degree of alignment of the sensor, but the parallelism can be promised to be ±0.5mm, and the viewpoint can be ±12°. However, if the parallelism error and viewpoint error are both large, the number jumps will appear. When this happens, it is necessary to adjust the parallelism and viewpoint.
3. The problem of wiring error of linear displacement sensor
The three wires of the linear displacement sensor cannot be connected incorrectly, and the power line and output line cannot be replaced. If the above wires are connected incorrectly, there will be a large linearity error. If there is a need, our company has a video of the wiring tutorial for your reference.
4. The problem of frequency modulation disturbance and electrostatic disturbance
Both FM and electrostatic disturbance may make the display of the electronic ruler jump digitally. Therefore, the signal line of the electronic ruler and the strong current line of the equipment should be separated from the trunking. It is necessary for the electronic ruler to be grounded mandatorically. The signal line needs to use a shielded wire, and a section of the electrical box should be grounded with the shielded wire. If there is a high-frequency disturbance, the voltage measurement of the multimeter will appear normal, but the displayed number will be non-stop; In the case of electrostatic disturbance, the situation is the same as that of high-frequency disturbance. To prove whether it is static disturbance, you only need to use a length of power cord to short connect the cover screw of the electronic ruler with some metal on the machine, and the static disturbance will be eliminated immediately after a short connection. However, if you want to eliminate the high-frequency disturbance, it is difficult to use the above method, you can try to pause the high-frequency disturbance source to see if the results will be better, so as to judge whether it is a problem of high-frequency disturbance.
5. The data is beating regularly, or there is no problem with the data
In this case, it is necessary to check whether the insulation of the connecting wire is damaged, and the short circuit to the ground caused by regular contact with the shell of the machine.
|
More on that
|
Analysis of sensor technical indicators - ifm
Because of the many technical goals of sensors, various data and literature have different perspectives, so that different people have different understandings, and even misunderstandings and ambiguities. To this end, the following are some of the top technical objectives of sensors:
1. Resolving power and resolution:
Definition...
|
|
Use of the ifm OGD580 laser distance sensor
The OGD580 is a spaced sensor (PNP type) with two digital output channels, each of which can be set to normally open, normally closed, or closed, depending on the requirements.
OGD580 consists of three parts: laser emitter, ...
|
|
Sensors in the mass flow controller – ifm
The mass flow manipulator is a new type of flow measurement and monitoring instrument, as well as an instrument that can conveniently monitor the activity of different gases in the pipeline without temperature and pressure compensation. Its working principle is to send the flow signal measured by the heating bridge of the sensor to the amplifier for amplification, and the enlarged ...
|
|
The difference between ifm inductive and capacitive sensors
There are many different series under ifm sensors, including inductive and capacitive sensors. So what's the difference between the two sensors?
ifm inductive sensors are essential in industrial use.
|
|
Torque sensors in industrial manufacturing – ifm
Torque sensor is a component that must be installed in some industrial products, mainly used to measure speed and viewpoint orientation, but different types of sensors have different ways to use and function, what is the classification of torque sensor?
Resistance strain ...
|
|
Factors influencing load cell performance – ifm
Load cells are an important category of load cells, the most widely used, and there are many ways to do so. In general, the composition of load cells is mainly elastomers, strain gauges, seals, etc. Several of them interact with each other to affect the function of the sensor, and their respective roles are as follows: ...
|
|
Presentation of the performance of the S-type load cell – ifm
1. S-type load cells are moderately priced and suitable for mass production - good sensor consistency is required, suitable for automated batch production, and high requirements for processing equipment to eliminate inconsistencies and faults formed by manual operation.
2 ...
|
|
How torque transducers work – ifm
1. Typical planning of torque sensors
Unlike load cells or force transducers, the measuring body of a torque transducer is not subjected to a tension load, but is torsionally affected by lever torque or torque. Therefore, torque transducers require special strain gauges to ...
|
|
Selection rules for pressure transmitters
Pressure transmitter is the most commonly used sensor in industrial practice, which is widely used in various industrial automatic control environments, touching water conservancy and hydropower, railway transportation, intelligent buildings, production automation, aerospace, military industry, petrochemical, oil wells, electric power, ships, machine tools, pipelines and many other occupations. ...
|
|
Wiring and installation of pressure sensors – ifm
Wiring method
The wiring method of various sensors is basically the same, and the pressure sensor generally has a two-wire system, a three-wire system, a four-wire system, and some five-wire systems.
The two-wire system of the pressure sensor is relatively simple, and one wire ...
|
|
Tips for setting CAN parameters for ifm controllers
1. ifm controller CAN parameters: communication cycle
In some applications, it is possible to set the monitoring time for SYNC packets generated by the master here.
Note that this moment is larger than the SYNC moment of the master. To go through the experiment ...
|
|
Sensors, temperature sensors, RTDs and thermocouples – ifm
RTDs and thermocouples are the most commonly used temperature sensing elements for temperature sensors. The operating principle of thermocouple temperature sensor is that the two ends of the contact surface of two kinds of incompatible metals produce a weak and weak voltage when the temperature is inconsistent, and the temperature is measured by expanding the electric, which is not necessary to measure the high temperature. RTD Temperature Sensors ...
|
|
The access point for load cell dashboards – ifm
Key points of maintenance of electronic crane scales, automobile weighbridges, electronic forklift scales, unique effect electronic scales, and the outer dial of Dongguan electronic weighbridge weight sensor:
The detection and analysis of problems in the application of load cells, and the common problems of the weighing appearance of automation technology have been in the end of the system software.
|
|
The structure of the sensitive core of the accelerometer
Accelerometers are the most important element in engineering vibration measurement. In the test system, the sensor is the first link of data acquisition and profiling, so the selection and correct use of the sensor will directly affect the quality and accuracy of the measured signal. Although people working on engineering vibration know that this ...
|
|
Precautions for the installation of high-frequency pressure sensors – ifm
The depth of the internal thread of the installation with the sensor should be greater than the length of the external thread of the sensor itself, so as to avoid the sensitive diaphragm of the sensor pushing to the bottom of the internal thread, so that the sensor is affected by stress.
If the size of the internal thread has been ...
|
|
The cause of sensor interference – ifm
1. The PCB layout board touches the problem, and when the imitation signal is traced, the imitation signal is not wrapped with imitation, and there is even a possibility that the signal line is directly taken to the power line, which is easy to receive disturbance.
Solution: When it is a board, wrap the GND to imitate the signal line. If there is a model ...
|
|
Select the appropriate mounting holes for ifm sensors
ifm sensors have a lot of precautions at the time of installation, and it is necessary to pay attention to the orientation of the device, if the device orientation is not suitable, it will also form damage to the pressure sensor.
The time and time requirements of ifm sensors in the installation ...
|
|
How sensor detection avoids interference – ifm
Sensor detection is known to prevent disturbances. Once disturbed, the sensor may be damaged, the measurement system will be affected, the inaccurate data will affect the future use, the judgment will be biased, and the impact can be large or small, so anti-interference is very important. Today we're going to comment ...
|
|
Installation steps for dynamic torque sensors
1. Transfer heat pipes for heat dissipation.
Dynamic torque sensors can be used in the production of viscometers, electric (pneumatic, hydraulic) torque wrenches, it has high precision, fast frequency response, good reliability, long life and other advantages.
Installation steps:
1. According to the connection mode of the shaft and the dynamic torsion...
|
|
Considerations for the selection of industrial sensors
1. According to the measurement object and measurement environment
In order to carry out a specific measurement operation, it is necessary to consider the principle of the sensor first, which requires an analysis of many factors. Since, even for the measurement of the same physical quantity, there are sensors with multiple principles to choose from.
|
|
Contact
working hours
