In order to ensure that the APCUPS power supply can continue to supply high-quality power to the computer even in the event of a power outage, it is important to equip the battery backup battery. When the load is not allowed to be powered, the UPS battery backup time in the communication room should be greater than the time from the mains power interruption to rehabilitation or to the time required for the normal power supply of the generator set (the front power supply system is equipped with a generator set), if this period is longer, it should be equipped with an external long-delay battery pack, but at this moment it should be admitted that the UPS internal rectifier can be charged with an external large-capacity battery pack, otherwise an external charger should be equipped.
The battery capacity should be selected in accordance with the principle that it is necessary for the battery to supply power to the inverter during the backup time, and the battery pack voltage should not drop below the minimum voltage allowed by the inverter at the rated load. When arranging the equipment in the computer room, the battery pack should be as close to the APCUPS host as possible, shorten the connection length of the two, and increase the cross-sectional area of the connection, so as to reduce the self-inductance of the connection and the voltage drop of the line.
The battery pack can be installed in the battery cabinet or in an open battery rack, the former is beautiful. It is neat, but it has higher requirements for the bearing of the floor slab, the latter can disperse the load-bearing, and the heat dissipation is good, but it covers a lot of land and is easy to accumulate dust, which brings inconvenience to maintenance.
|
More on that
|
Frequency converters and their control – Schneider
AC inverter is the result of the high development of microcomputer and modern power electronics technology. The microcomputer is the center of the inverter, and the power electronics form the main circuit of the inverter. As we all know, the frequency of communication electricity sent from power plants is stable and constant, in our country it is 50 weeks per second ...
|
|
Precautions for the installation of low-voltage electrical appliances - Schneider
1. Low-voltage electrical appliances should be equipped in a place without violent vibration, and should have an appropriate height from the ground. It is necessary to connect the power cord such as the knife switch and the load switch to the fixed contact, and it is forbidden to hang the power cord on the knife switch.
2. Low-voltage ...
|
|
Servo motor selection process – Schneider
1. Load organization (acknowledging the type of tissue and its specific data, such as ball screw length, ball screw diameter, stroke, pulley diameter, etc.)
2. Form of action (acknowledging the form of action of manipulating the target, the relationship between time and speed; Will manipulate ...
|
|
Schneider UPS power supply common fault analysis
1. When there is mains power, the UPS output is normal, and when there is no mains power, the buzzer beeps for a long time and there is no output
Fault analysis: From the phenomenon to identify some problems of the battery and inverter, you can view it according to the following procedures:
1. Check the battery voltage to see if the battery is undercharged.
|
|
Schneider inverter control circuit
1. What is a control loop?
The network that supplies the control signal to the main circuit that supplies power to the asynchronous motor (voltage and frequency can be adjusted) is called the control loop.
Second, the composition of the control loop
The control circuit is controlled by the frequency ...
|
|
Schneider inverter knowledge points
1. Use the analog output port to indicate the motor frequency, when the motor frequency is 50Hz, why is the output only 16mA?
Due to the maximum output frequency parameter of the inverter "TFR", the factory default value is 60Hz. So when the inverter output is 50Hz, the analog output is 16mA. At this time, only ...
|
|
Whether an AC circuit breaker can be used in a DC circuit
Schneider circuit breakers are used to open and break communication loops. The arc extinguishing of the communication system is simple, but the arc extinguishing of the DC system is more difficult. Because the system is different and the arc extinguishing principle is different, there is a big difference in structure and performance between the communication circuit breaker and the DC circuit breaker. Compared with the communication circuit breaker, the DC circuit breaker ...
|
|
Schneider relay model introduction
RM4 Series Control Relay (Three-phase Power Control)
RM4 series voltage steerable relays
RM4 current operated relay
RM4 level control relay
RM17 three-phase power controller
RM35 3-phase power control relay
RM17 Voltage Steerable Relay ...
|
|
Schneider inverter has misunderstandings in practical applications
Myth 1: Whether the inverter can complete power saving
The use of inverters can save electricity Some literature claims that inverters are power-saving control products, giving people the impression that only the use of inverters can save electricity. In practice,
The reason why the inverter can save electricity is because it can ...
|
|
Schneider ATS48 soft starter issue
1. What type of ATS48 power supply is?
The control power supply of ATS48 selects communication input, and supplies power to the controller, input and output ports through internal power processing;
The control power supply of Q series products is 220V-415V;
Handling of the Y-Series ...
|
|
Pressure Reducing Valve in Instrumentation – Schneider
A kind of pressure reducing valve in instrumentation refers to a kind of equipment used to control the pressure value. Pressure reducing valves are usually used in water-related categories, because from the perspective of the transmission medium, the transmission medium of the equipment is mainly water, but we all know that water is a thing that will ...
|
|
Schneider Lexium ILA all-in-one AC servo
The Schneider Lexium integrated drive consists of an electric motor and a control circuit that announces the control signal via a fieldbus, pulse/direction interface or I/O interface (for internal motion tasks).
High compactness: motor and control circuits ...
|
|
Instrumentation overhaul points - Schneider
The test input does not conform to the "short" rule, and the problem is here.
1. Overhaul according to the comparator rules, fit it, the piece is good, and check the periphery; It doesn't fit, the piece is bad.
2. It does not fit the "virtual break" - there are ...
|
|
Schneider seizes the opportunity of e-commerce
Beijing, China, 24 August 2021 – Looking at the history of the logistics industry, the changes brought about by the development of e-commerce in recent years are rare. According to Digital Commerce 360, in 2020, United States customers spent $861.12 billion online, a year-on-year increase.
|
|
Schneider inverter ATV32 acceleration and deceleration operation method
1. Use the operation method of clicking the button:
In addition to the direction of travel, 2 logic inputs are required to add a speed given, e.g. LI5 is assigned the acceleration function, and LI6 is assigned the deceleration function. Then pressing LI5 will make the speed given increase, and pressing LI6 will make the speed given speed decrease ...
|
|
Pay attention to the problem when using UPS power supply - Schneider
1. The parameters set in the host cannot be changed at will during use. In particular, the parameters of the battery pack will directly affect the service life. With the change of ambient temperature, the float charge voltage should be adjusted accordingly. Generally, 25 °C is the standard, and when the ambient temperature rises or falls by 1 °C, the float charge ...
|
|
The type of signal output from the Schneider sensor
The type of sensor output signal
Sensors are commonly used detection devices that convert perceived information into electrical signal outputs, and are used in a variety of applications. What can be divided into the output signal mode of the sensor ...
|
|
The inverter controls the speed of the AC motor – Schneider
Most of the motors used in the industry are of this type. The rotational speed of an induction AC motor (henceforth referred to as a motor) is approximately determined by the number of poles and frequency of the motor. The number of poles of the motor is fixed by the working principle of the motor. Since the pole ...
|
|
Turbine flowmeter selection factor - Schneider
Turbine flowmeter is a kind of speed appearance, it has high precision, good repeatability, no zero drift, high range ratio, simple structure, few moving parts, high pressure resistance, wide measurement scale, small size, light weight, small pressure loss, convenient repair and other advantages, turbine flowmeter has high quality ...
|
|
Schneider inverter series at a glance
1. ATV11 series
The Schneider ATV11 series is primarily used in three-phase asynchronous motor inverters with a power range of 0.18 to 2.2 kW.
2. ATV12 series
ATV12 Schneider inverter for power scale 0.18k...
|
|
Contact
working hours
