The new radar level sensor LW2720 with IO-Link interface

The first step is the ambient temperature, what is the normal temperature? 25±15°C, if there is a regular measurement temperature of the measured specimen, then the regular temperature shall prevail; The second step, the condition of the product, that is, the normal operating condition, ...

How it works Static pressure measurement principle: when the liquid level sensor is put into a certain depth in the liquid to be measured, the pressure on the liquid surface of the sensor is formulated as: Ρ = ρ .g.H + Po formula: P: The pressure on the liquid surface of the transmitter ...

Changes in mechanical spacing can be detected directly and parameterized easily via the IO-Link interface Interval measurement provides robust endpoint position detection High quality stainless steel housing (316L) The temperature scale is the most ...

RTDs and thermocouples are the most commonly used temperature sensing elements for temperature sensors. The operating principle of thermocouple temperature sensor is that the two ends of the contact surface of two kinds of incompatible metals produce a weak and weak voltage when the temperature is inconsistent, and the temperature is measured by expanding the electric, which is not necessary to measure the high temperature. RTD Temperature Sensors ...

On July 9, 2018, the grand Red Dot Awards ceremony was held at the Aalto Theater in Essen, Germany, and the prestigious "Red Dot Planning Award" 2018 was presented. This year's contestants from 59 countries paid tribute to the Red...

The pressure sensor is an instrument that can accept pressure signals, and it is widely used in railway transportation, intelligent buildings and other occupations. First, prevent solder slag from ...

A load cell (also known as a load cell) is a type of sensor that converts a physical force signal into an electronic signal. From the basic principle, it is divided into strain type, piezoresistive type, piezoresistive type, foot type, etc. Non-repeatability: In the same ring ...

(1) Large-scale In order to obtain accurate information, many sensor nodes are usually arranged in the monitoring area, perhaps in the tens of thousands, or even more. The large-scale nature of the sensor network contains two implications: on the one hand, the sensor nodes are distributed in a large geographic area, such as in the original ...

The conversion of the pressure to the electrical signal is done by the physical deformation of the strain gauge, and the strain gauge is bonded to the diaphragm of the pressure sensor and wired into a Wheatstone bridge structure. The pressure exerted on a high-frequency pressure sensor causes the diaphragm to flex, which causes the strain gauge to strain. Strain will occur ...

The first step in selecting a pressure sensor is to determine the pressure to be measured. Exciter sensors are divided into mechanical pressure and pneumatic pressure (hydraulic). The mechanical pressure unit is generally N.KN.KGF, etc. The pneumatic and hydraulic units are generally KPA, MPa, PSI, etc. This article describes the selection of mechanical pressures. ...

1. ZCS1100 fine capacitance displacement sensor. This sensor can detect piezoelectric micro-displacement, shaking table, electron microscope fine-tuning, astronomical telescope lens fine-tuning, fine micro-displacement measurement, etc. The sensor is a single channel, high-performance linear displacement measurement system, innovative ...

Vortex flowmeter series instrument because of the use of the environment is special or harsh in the field work sometimes present such and such problems, resulting in production will be affected, vortex flowmeter and orifice flowmeter and V-cone flowmeter are different, as far as the orifice flowmeter is concerned, it is the standard orifice plate and multi-parameter ...

A differential pressure sensor is a sensor used to measure the difference between two pressures, usually used to measure the pressure difference between the front and rear ends of a device or component. A typical application of differential pressure sensors is to measure the difference in exhaust pressure between the front and rear channels of the exhaust particulate trap of a passenger car engine.

1. The programming method of the programmable ifm controller is simple and easy to learn Programmable ifm controller ladder diagram is the programming language of the more used PLC, its circuit symbols and expressions are similar to the schematic diagram of relay circuits, the ladder diagram language is intuitive, easy to learn and understand, understand the relay ...

Don't panic when you encounter a problem with the pressure sensor, you should find a way to solve it, if the pressure rises, the transmitter output will not rise. In this case, first look at the pressure sensor pressure interface to see if it is leaking or blocked; If not, check the connection form and power supply; If...

As an accurate detection device, if the sensor is damp, it will be troublesome, the sensor will affect its accuracy and stability when it is damp, and it will form a problem if the sensor is used in a more important place, then the loss of the formation is very heavy. In '08 there was a ...

1. The size of the measured oscillation; 2. The frequency scale of the oscillating signal; 3. The environment of the oscillation test site; 1) Selection and measurement scale of the sensitivity of the oscillation sensor Estimating the amount of oscillation will help ...

Sensitive parameterization, diagnostics and data processing of ifm sensors are suitable for many different uses9 versions, suitable for a variety of different types of sensitive parameterization, diagnostics and data processing with I/O-Link Ideal for the identification of small data volumes with LR DEVICE or IO-L ...

1. The ifm controller has a control function Another important reference feature for the purchase of ifm controllers is the ability to control movements and other applications. Fulfillment of these functional requirements requires I/O, as well as a strong processor and the ability to prioritize missions. Programmable Drum Switches (PDS...

1. Resistance strain gauge The resistance strain gauge is a resistance wire mechanically distributed on a substrate made of organic materials, that is, it becomes a strain gauge. An important parameter for him is the sensitivity coefficient K. When his ends are subjected to the F force, they will elongate, that is, they will be deformed. ...