Frequently asked questions about the myPNOZ safety relay of the new generation

Applications for Solid State Relays (1) The recommended value of the foreign SSR trigger signal (i.e., the current through the light-emitting tube) is 10mA DC, and the recommended value of the domestic SSR trigger signal is 12-25mA DC. (2) Multiple SSRs can use the same trigger signal, which is common in the control of three-phase AC loads.

When the input quantity (such as voltage, current, temperature, etc.) reaches the specified value, the electrical appliances that make the output circuit to be controlled on or off can be divided into two categories: electrical quantity (such as current, voltage, frequency, power, etc.) relays and non-electric (such as temperature, pressure, speed, etc.) relays.

1. Control wiring: You think of it as a DC relay. 3. 7 is used to connect to 12V control voltage; 2. 7 is used to connect to 24V control voltage. In the meantime, 7 is used as the negative electrode of direct current, and it is connected to the neutral line when used. 2. Connect to the front of 220V. Second, the operation control: although the control voltage is connected ...

In the context of industrial automation, the term "safety" refers to the functional safety of equipment, which means that people and the environment are protected from damage from foreseeable coercion from machines, and the residual risk is more or less always present, but the residual risk cannot exceed the acceptable level. Through the use of security relay ...

(1) Measure the resistance of the contact: use the resistance of the multimeter to measure the resistance of the normally closed contact and the moving point, and the resistance value should be 0; The resistance between the normally open contact and the moving point is infinite. From this, it is possible to distinguish which is a normally closed contact and which is normally open. (2) Coil resistance: multimeter R...

IO-Link is an open sensor communication protocol that represents a powerful and standardized (IEC 61131-9) connection technology in the field of point-to-point communication and is fieldbus and system independent. The communication protocol will also be used for functionally safe data exchange in the near future. The advantages of IO-Link are ...

With the rapid development of industrial technology, on-site equipment is also developing towards a high degree of integration and automation. But no matter how the technology develops, behind the dazzling technology, the basic common equipment is always a solid backing. The hydraulic press is one of the old industrial basic equipment, and it is almost ...

The "Safety Standardization" theme exhibition organized by the China Machinery Industry Safety and Health Association and the National Machinery Safety Standardization Technical Committee was unveiled at the China Yiwu International Commodities (Standards) Expo held from November 24 to 27, 2022. Automation specialist Pilz was invited to participate in the exhibition to demonstrate ...

With the increasing functional requirements of industrial production, the continuous optimization of process levels and the escalation of the complexity of production conditions, systems that effectively record and manage relevant data are particularly important for machine safety, especially for production safety. PITreader Authorization ...

Recently, the inaugural meeting of the Youth Safety Expert Working Committee of China Machinery Industry Safety and Health Association and the first China Equipment Manufacturing Youth Safety Expert Forum were held in Chengdu, Sichuan.

The most common ones are the following: (1) Contact failure 1. The phenomenon that cannot be disconnected due to mechanical occlusion of the contact (the needle-like protrusion formed on the contact and the pit biting each other), fusion welding, or cold welding. 2. Due to the contact resistance becoming large and unstable, the circuit cannot be normal ...

1. The installation of the safety grating must be able to effectively prevent bypassing the detection area of the safety grating and contacting the dangerous moving parts, that is to say, the detection area of the installation grating can not have a blind spot, if the top or bottom of the safety grating has a fixed guard, the guard should be able to ...

Pilz supports manufacturers and operators of packaging machines in the implementation of packaging automation. As a well-known and trusted provider of machinery safety services to companies worldwide. Use the myPNOZ modular safety relays The first ...

1. Y0 is connected to one end of the coil A1 of KA1; 2. The other end of KA1, A2, is connected to 24V; 3. Y1 is connected to A1 at one end of the coil of KA2; 4. The other end of KA2 A2 is connected to 24V; 5. COM terminated to 24V. ...

The tightly meshing beam field of the safety light curtains PSENopt and PSENopt II is ideally suited for all applications where hand protection is required. By placing the safety light curtain close to the danger zone, the operator can be optimally protected and the workflow will not be interrupted, making it ideal for spaces with ...

Generally speaking, the input control voltage of the solid state relay is 3.2-32V. The control current is 5-30mA.Usually the SSR input circuit of 1-2 is not a constant current source circuit, and the input control voltage is 4-16V. The control current is 5-20mA, and the SSR input circuit with the larger rated current is connected to the constant current source ...

An autonomously running burner management system has a complex structure and must comply with many international standards. Due to the high level of danger, strict safety regulations need to be applied to avoid the presence of unburned fuel in the combustion chamber. Pilz has a safe burner management system specifically tailored to these requirements. ...

AS MENTIONED EARLIER, PILZ SAFETY RELAYS ARE THE MAIN COMPONENTS FOR CONTROL CIRCUITS AND MONITORING AND PROTECTION SYSTEMS FOR ELECTRIC LOCOMOTIVES. When the locomotive is running, when the motor, electrical appliances or connection lines in the main circuit and auxiliary circuit fail, the fault can be replaced by the Pilz safety relay of the corresponding monitoring and protection system.

Pilz safety relays generally consist of an iron core, a coil, an armature, a contact reed, etc. As long as a certain voltage is added to both ends of the coil, a certain current will flow through the coil, resulting in an electromagnetic effect. Under the action of electromagnetic attraction, the armature overcomes the pulling force of the return spring and sucks in the iron ...

1. Whether the control voltage of the relay module is consistent with the system voltage. 2. It is still possible to use high level and low level for the level control mode of the relay module. 3. Depending on the requirements, choose whether you need a fully isolated relay module. 4. Safety: Relay ...