Steps on how to connect Omron NX to Willuntong touch screen Ethernet

1. DIP switch mode touch calibration and system initialization. For the full eMT series, MT8000i series, TK series, WT series and other HMIs, there is a set of reset buttons and DIP switches, which can trigger the corresponding functions when switching between different modes. If the HMI touches ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. There are generally three ways to enter the system setting of the TK6070ih touch screen: 1,Generally in the lower right corner of the touch screen, ...

Due to the technical limitations and different equipment environment, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the touch screen also needs regular maintenance like ordinary machines, and because the touch screen is a touch all-in-one machine with a high degree of integration of a variety of electrical equipment, so in ...

1. Why can't the screen display Chinese normally, but the display is garbled? Answer: This situation is generally caused by not choosing the correct Chinese font, just choose a Chinese font, the specific operation steps are as follows: 1) In EasyBuilder soft...

The R&D team of Weiluntong Technology has launched an Internet of Things intelligent communication gateway for the solution of "data transmission and integration of the Internet of Things": cMT-G01. With the rise of the concept of the Internet of Things and the emergence of various smart factories, you will face the biggest dilemma as an engineer ...

1. Connect the touch screen with the PLC We know the communication between two pieces of hardware, whether wireless or wired. The first step is to establish a connection. The most common connection between PLC and touch screen is serial data cable connection. The data cable can be used in a treasure ...

1. First of all, open the Weiluntong touch screen and enter the application. 2. Secondly, select "Edit" → "Personalization" on the control bar of the window. 3. Finally, set the picture to the bottom layer. ...

1. Enter the system settings interface of the Weilun touch screen, and select the "Power Management" option in the "System Settings". 2. In "Power Management", you can set how long the touch screen will automatically enter the "standby" state without operation, and you can also set how long it will enter the "...

1. The power cord is not properly connected This may seem obvious, but make sure the power cord is connected to the back of the touchscreen and plugged into a power outlet. If it looks like it's connected correctly, disconnect and reconnect both ends of the power cord to make sure the cable isn't loose. 2. The power cord is damaged ...

When using the Weiluntong touch screen, how to set the IP address Examples: CMT2109X2 and CMT2079X First of all -> click on the little yellow button on the touch screen Secondly -> Click on the lock symbol Again-> Enter the password by default 111111 And then-〉 ...

Gesture control is like swiping a mobile phone, and industrial products are no longer monotonous and boring The new cMT X-Series HMI supports touch gestures. Users can swipe, grab and other gestures to operate the interface, and no longer need to use buttons, they can operate functions on the HMI, providing more convenient and more ...

1. Set through the system parameter settings: menu bar [Common] - [System Parameters] - [General Attributes] - [Screen Saver Settings] If the screen saver time is set to 25 minutes (equal to 25 written in LW9081), the screensaver window is 80, from the time the program is downloaded to the HMI is turned on, 25 ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

1.1 How to delete the job button on the taskbar of the touch screen? Set "Modify/Set System Parameters/General/Job Buttons/Features" to "Closed". 1.2 What does RS485 Default/RS485 2W/RS485 4W Separation mean in the communication port type? r ...

3.1 What should I do if the touch screen shows garbled characters? Select "Oriental Language" in the EB500 software "Options/Language Selection", and then compile it after saving it so that there will be no garbled characters. 3.2 Why can't the following window appear when editing EB500 software, and it is blank? ...

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...

1. Plug in the U disk on the touch screen, you don't need to power off the screen, the screen supports the hot-swap function, but at this time, it is best not to communicate with external devices to reduce unnecessary impact. When the screen detects an external device, a dialog box will pop up, select the second Upload Project option ...

1. The touch screen controls the inverter through PLC 1. At present, the general control inverter needs to use PLC to communicate with the inverter, read the information of the inverter, and then the touch screen communicates with the PLC to complete the control of the inverter to start and stop, and monitor the operation of the inverter.

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power on again, a white cross cursor will appear on the screen, click the middle of the cross cursor vertically, after the point (the time can not be too short), the cross cursor will automatically jump to the next position, the cross light ...

1. Check whether the power supply of the host is working normally. First, check whether the host system is powered by checking whether the power indicator on the host chassis panel is on and whether the power supply fan is rotating. Secondly, use a multimeter to check whether the external voltage meets the requirements, the voltage is too high or too ...