How to enter the system settings of the MT6070ih screen

1. Touch failure; 2. Touch the glass plate is broken; 3. The key is damaged and the key is not effective; 4. White vertical bars, horizontal bars, and bright lines appear; 5. Half can be touched, half can not be touched; 6. Can't enter the program; 7. The touch screen cannot be calibrated.

3.1 What should I do if the touch screen shows garbled characters? Select "Oriental Language" in the EB500 software "Options/Language Selection", and then compile it after saving it so that there will be no garbled characters. 3.2 Why can't the following window appear when editing EB500 software, and it is blank? ...

Transparent properties Transparency, which directly affects the visual effect of the touch screen. Transparency has the problem of transparency, infrared technology touch screen and surface acoustic wave touch screen are only separated by a layer of pure glass, transparent can be regarded as a leader, other touch screens should be carefully scrutinized, "transparent", ...

1. If you are using a capacitive touch screen, then it is recommended that you first install the driver required for the capacitive touch screen correctly according to the requirements of the manual when you use it for the first time, and then click "Start"/"Program"/"Microtouch Touc" on the screen with your fingers.

Ambient light factor, infrared receiver tube has a working range between minimum sensitivity and maximum illumination, but touch screen products can not limit the range of use, from the dark cabaret room to the outdoor use under the high-intensity sunlight on Hainan Island, as a product, it must adapt. Rapid detection ...

Weiluntong touch screen, also known as "touch screen", "touch panel", is a kind of inductive liquid crystal display device that can receive input signals such as contacts, when touching the graphic buttons on the screen, the haptic feedback system on the screen can drive various connection devices according to the pre-programmed program, which can be ...

USB cable specification: HI-SPEED USB Revision 2.0 SHIELDED 24AWG 1. The USB port of the computer must support standard USB 2.0 or USB 3.0. 2. The USB cable needs to be double-layer isolated: aluminum foil and copper mesh isolation. 3. The length of the USB cable is not ...

Due to the environmental adaptability of Weilun touch screen, especially the surface sound wave screen, the screen will affect the normal use due to water droplets, dust and other pollution, so the touch screen also needs regular maintenance like ordinary machines. 1. Wipe the screen with a dry cloth every day before turning it on.

To change the IP address of the touchscreen, you need to click the arrow below the touchscreen. Then enter the original password of the touch screen in the pop-up interface: 111111. After that, enter the IP setting interface. Enter the interface to set the IP address you want to set, and finally remember to click after setting ...

1. Enter the system settings interface of the Weilun touch screen, and select the "Power Management" option in the "System Settings". 2. In "Power Management", you can set how long the touch screen will automatically enter the "standby" state without operation, and you can also set how long it will enter the "...

1. Background color: Right-click on the blank space of the window, select Properties, Pop-up Settings, and select a color in the background; Hatch: In the background, tick the fill, select the pattern color and pattern. 2. Picture/Background Image: Select Picture Element ...

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

1. The motherboard cannot recognize/display the peripheral devices. 2. The peripherals will stop working for a few seconds or more. 3. A slow boot may indicate that your motherboard is broken, although it could also be other components. 4. The touch screen does not recognize the flash drive, or ...

1. When turning on and off the power of the machine, it should be operated in strict accordance with the regulations; 2. According to the severity of the environment, set a time limit to open the machine head to clean the reflective stripes and inner surface of the touch screen; 3. At present, the mainstream industrial display program does not have a mouse cursor, because the flashing of the cursor will ...

Virtual serial port configuration process: 1. Open the virtual serial port configuration software and create two pairs of serial ports; 2. The circle is the physical serial port in the computer, and the virtual serial port in the box; 3. Two groups have been added, and friends who want to add port tests can do so in the window on the right.

1、eMT3120A 12.1" TFT display 1024*768 dots, brightness 500, contrast ratio 700:1, 16.2M color, 256MB memory, DC19.2-28.8VDC power supply, four-wire resistive, SD card slot, support SD/SDHC, USB Host USB 2.0 ...

1、MT6102iQ 10.1" TFT display 1024*600 dots, brightness 350, contrast ratio 500:1, 16.7M color, 128MB memory, DC10.5-28VDC power supply, four-wire resistive type, USB Host USB2.0/Serial Interface (Con.A COM2 RS-485 2W/...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

First, check whether the wiring interface is loose, and then check whether there is a conflict between the serial port and the interrupt number, if there is a conflict, the resources should be adjusted to avoid the conflict. Then check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the surface of the touch screen for dirt and dirt.

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...