When the LS power generation module is put into operation, its working process is generally divided into three stages: input sampling, user program fulfillment, and output rewriting. The completion of these three phases is called a scan cycle. Throughout the entire operation, the PLC's CPU repeats the above three phases at a certain scanning speed.
(1) Input sampling stage In the input sampling stage, the PLC reads all input conditions and data sequentially in a scanning manner, and stores them in the corresponding unit in the I/O image area. After the input sampling is complete, it moves to the user program fulfillment and output rewriting phase. In both phases, even if the input status and data change, the condition and data of the corresponding cells in the I/O image area will not change. Therefore, if the input is a pulsed signal, the width of the pulse signal must be greater than one scan period to ensure that the input can be read in any case.
(ii) User program fulfillment phase
During the user program fulfillment phase, the LS power generation module always scans the user program in a top-down order (ladder diagram). When scanning each ladder diagram, the control circuit composed of each contact on the left side of the ladder diagram is always scanned first, and the control circuit composed of contacts is logically operated according to the order of first left and then right, first up and then down, and then according to the result of logical operation, the condition of the corresponding position of the logic coil in the system RAM storage area is rewritten; Or override the position of the output coil in the I/O image area; or determine whether to perform a special utility instruction that is governed by the ladder.
That is, in the process of user program fulfillment, as long as the status and data of the input points in the I/O image area will not change, and the conditions and data of other output points and soft devices in the I/O image area or the system RAM storage area may change, and the ladder diagram ranked above, the program performance result will play a role in the ladder diagram of all coils or data used in the below; Conversely, the condition or data of the overwritten logic coils in the ladder diagram below can only be used for the program above it until the next scan cycle.
In the process of program execution, if the immediate I/O command is used, the I/O point can be accessed directly. That is, if the I/O command is used, the value of the input process impression register will not be updated, the program will take the value directly from the I/O module, and the output process impression register will be updated immediately, which is a little different from the immediate input.
(iii) Output rewriting phase
When the user program is scanned, the LS power generation module enters the output rewriting stage. During this period, the CPU overrides all the output latch circuits according to the corresponding conditions and data in the I/O image area, and then drives the corresponding peripherals through the output circuits. At this time, it is the real output of the PLC.
|
More on that
|
The difference between multi-function inverter and general-purpose inverter - LS produces electricity
With the deepening of factory automation, the high efficiency and low cost of active warehouses, elevators, transfer systems, etc., as well as the high speed, high efficiency and high precision of small CNC machine tools, kneading and forming machines, textile and film machinery, etc.
|
|
The main functions and functions of LS power production PLC
1. For sequential control: sequential control is based on the current and pre-historical conditions of the input switch, and produces the required switching output, so that the system can work in a certain order. This is the basic manipulation of the system. It is also a common manipulation in discrete production processes.
...
|
|
Parameter setting of LS power inverter
Control method: i.e. speed control, rotation control, PID control or other methods. After adopting the control method, it is generally necessary to carry out static or dynamic identification according to the control accuracy and requirements. Low operating frequency: that is, the small speed of the motor running, when the motor is running at low speed, its heat dissipation function ...
|
|
The choice of inverter power - LS produces electricity
1. The power value of the inverter is the most suitable for the power value of the motor, so as to facilitate the operation of the inverter at a high power value.
2. When the power classification of the inverter is not the same as the power classification of the motor, the power of the inverter should be as much as possible.
|
|
LS electric braking unit functions, advantages and operation process
First, the main function of the braking unit
In some applications, the need for rapid speed reduction, according to the principle of asynchronous motor, it can be known that if the slip is larger, the greater the torque, the same braking torque will increase with the increase of the speed reduction rate, so that the system speed reduction time is greatly shortened, and the energy feedback is greatly ...
|
|
The inverter selects the appropriate peripheral equipment - LS power generation
After we have selected a suitable Variable-frequency Drive (VFD), we also need to consider whether we need to equip other peripheral equipment according to the actual situation of the site. The peripheral equipment selected by VFD mainly includes circuit breakers, reactors, contactors, braking resistors, etc.
...
|
|
Several basic functions of the inverter - LS generates electricity
The inverter mainly has the following functions:
1. Soft up
The direct launch of the inverter motor will have a severe impact on the power grid, and it will also have too high requirements for the capacity of the power grid, which is extremely unfavorable to the service life of equipment and power grid circuits.
|
|
LS power terminal is faulty
From the perspective of application, the function of the terminal block should be achieved: the contact part should be conducted, and the contact should be reliable. The insulating parts should not be conducted, and it is necessary to insulate them firmly. There are three common forms of fatal failure of terminal blocks:
...
|
|
LS GTH, GTK series thermal relay models
Thermal Overload Relay GTH-22
GTH series: GTH-22, GTH-40, GTH-85, GTH-100, GTH-150, GTH-220,
GTH-400、GTH-600、GTH-12M、GTH-12MH、GTH-12M、GTH-MH
GTH series: GTH-22, GTH-40, GTH-85 ...
|
|
The method of judging the quality of components - LS power production
1. Detection of ordinary diodes
Use the MF47 multimeter to measure, connect the red and black watch pens to the two ends of the diode, read the reading, and then adjust the watch pen to measure. According to the results of two measurements, the forward resistance value of the general low-power germanium diode is 300-500Ω, and the silicon diode ...
|
|
The wiring distance between the motor and the inverter
Burn two new motors in a row! The output current and voltage of the inverter are balanced, the input voltage is balanced, the current is unstable, and the fluctuation is 20%-50%, the inverter is burned off by a short circuit between 35Hz turns, the grid voltage is very stable, 720V, the interval between the motor and the inverter is 120m, and the input and output terminals of the inverter are powered ...
|
|
Inverter carrier frequency adjustment method - LS power generation
A． The output voltage of the SPWM inverter is a series of pulses, and the pulse frequency is equal to the carrier frequency.
B. In the current of the motor, there is a harmonic component with a strong carrier frequency, which will cause the vibration of the motor core and announce the noise. If the frequency of the noise is the same as that of the motor core.
|
|
LS Electric reached a strategic cooperation with Nandu Power Supply and Changzhou Kunlan
Due to the "new infrastructure" policy, the Chinese government has vigorously promoted the new energy and ESS markets, and according to CNESA, the cumulative electrochemical energy storage scale in China will reach 19.3GW in 2023, which is expected to exceed 20% of the global market.
June 3 ...
|
|
Advantages and disadvantages of LS inverter non-sensing vector control
The first generation of LS inverter selects the voltage frequency ratio scalar control method, which carries out frequency conversion speed regulation according to the linear ratio determined by the equivalent circuit of the asynchronous motor. Voltage refers to the effective value of the fundamental wave, and changing U/f can only regulate the steady-state magnetic flux and torque of the motor, not to mention dynamic control. In order to improve the low ...
|
|
Fault solution for three-phase asynchronous motor - LS power generation
1. The motor cannot roll after being energized, but there is no abnormal noise, no peculiar smell and smoke.
1. Cause of the problem: (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring of the control equipment is faulty.
2. Question ...
|
|
Manufacturing Automation Terminology – LS Electricity Generation
I/O Points:
When discussing control systems, I/O points are a term that is often heard. It refers to the input/output point, I stands for INPUT, which refers to the input, and O stands for OUTPUT, which refers to the output. The inputs/outputs are for the control system, and the input refers to the ...
|
|
An internal component of LS's power circuit breaker
1. Auxiliary contact: the contact mechanically linked with the main circuit of the circuit breaker and the closing mechanism is mainly used for the display of the circuit breaker and the closing status, and is connected to the control circuit of the circuit breaker through the opening and closing of the circuit breaker to control or interlock its related electrical appliances. For example, output to signal lights, relays, etc.
|
|
Precautions for the maintenance of the inverter of the tensile testing machine - LS generates electricity
In the course of regularly checking the variable-frequency drive (VFD) of the tensile testing machine, we can visually check the operating status directly from the outside.
(1) The ambient temperature is normal, and it is required to be between -10°C and +40 ...
|
|
LS Electric's motion control system solution on pillow (horizontal) packaging machine
The pillow packaging machine mainly performs the operation of product forming, positioning, packaging and sealing, etc., and the equipment is composed of the packaging film shaft that provides the packaging film, the feeding shaft that provides the material, the cutter shaft that performs the sealing and cutting operation and the discharging shaft after the product packaging is completed, and the equipment structure diagram is as follows:
...
|
|
A brief description of the K120S series plc
K120S series PLC product is a unit PLC product introduced to the market by LS in 2004, which has laid a solid foundation in the low-end small machinery supporting industry with its high-performance price ratio. Relying on some special functions of the product, it has also won some industry praise.
...
|
|
Contact
working hours
