How to use Rittal cabinets

Create Date: 2024-8-30 12:03:23|Source: Rittal/Rittal

1. Tie the cable tie at the beginning of the root of the cable with a cable tie, if there are too many cables, the number of the network cable is divided into two or many parts from the center, but the demand ensures that each part of the network cable is connected, because the next step is simple.

2. According to the demand for most of the network cables to tie up the beginning with the distribution board to manage the wire, the use of the distribution board is to follow the agreement to pass the cable from the back of the distribution board through the distribution board one by one, in the back of the distribution board according to the two connected network cables with a reuse of the cable tie up, every two tie a piece requires a dislocation, that is, do not tie too much side by side, every two cable ties up and down the best distance, two connected ties up and down in the future to start six network cables together together, the average demand every half a meter from the beginning of the tie together, Pay attention to the neatness when you tie it, and don't mess with it to give people a feeling of disharmony.

3. The use of the cable management board has always been moved downward, and the back of the cable management board has always been wrapped with a cable tie for half a meter). In the end, the orientation of the six roots at a time is about one meter at the end of the offline cable, and the two roots are tied at the beginning of the nearby distance in the future, of course, they are tied in order. After every two roots are tied, use the same method to tie again about half a meter down, which is conducive to the next step of playing the distribution frame.

4. The following is the beginning of the distribution frame, because the above work has been completed, the cable has been very clear in the future, throw the cable to the outside of the cabinet and place it on a job table in a group of three to start the line pressing operation. It is not easy to make a mistake when pressing the line according to the pre-arranged orientation.

5. Test the patch panel, test the device on the cabinet, if you find that there is no point to carefully check the contact and line sequence of the network cable and the module, and strive to pass through it for a while, in the future when the test module is all pressed, the end of the device on the cabinet, after installation, the network cable is tied according to the original plan, so that the neatness is beautiful, horizontal and vertical. The connectivity of each point is recorded, and if it is never possible to pass through the requirements, it is recorded in the fill log. Facilitate follow-up examinations.

More on that

	Rittal Cables - What are the main contents of cables? 1. SYV: solid polyethylene insulated RF coaxial cable, coaxial cable, radio frequency signal transmission in wireless communication, broadcasting, monitoring system engineering and related electronic equipment (including comprehensive coaxial cable) 2. SYWV(Y): Physical Foamed Polyethylene Insulated Cable TV System Cable, Video ...
	Common faults and solutions for Rittal cabinet air conditioners If the indoor temperature is higher than the outdoor one, or the indoor temperature is higher than the set temperature, the air conditioner will not start; Solution: Test the temperature comparison between indoor and outdoor to check whether the indoor temperature is too high. The voltage of the air conditioner is unstable, and the compressor cannot be started normally.
	Rittal cables – the basic structure of power cables 1. Core: The core is the conductive part of the power cable, which is used to transmit electric energy and is the main part of the power cable. 2. Insulation layer: The insulation layer is to electrically isolate the core from the ground and the cores of different phases to ensure the transmission of electric energy.
	Introduction to the process characteristics of the Rittal cabinet - PS frame universal control cabinet 1. The cabinet door is 25mm from the ground and 2.5mm thick mounting plate, and there are 20mm wide U-shaped curved edges on both sides, which makes the mounting plate stronger and easy to handle. 2. The three cable introduction cover plates at the bottom of the box can be replaced with each other, which is easy to move, easy to import cables, and easy to open holes into the line. 3 ...
	Rittal enclosures – Q&A on the basics of high- and low-voltage distribution cabinets What is Arc? Arc is a physical phenomenon generated during the operation of electrical equipment, which is characterized by very strong light and high temperature. Classification of electrical loads? Primary load: those whose power supply interruption will cause personal injury or death; or those that will cause significant losses politically or economically. ...
	Rittal cables – the common code for cables Usage code - not marked as power cable, K- (control cable), P- (signal cable); Conductor material code - not marked as copper (can also be marked as CU), L- (aluminum); Inner Sheath Code – Q-(Lead Packed), L- (Aluminum Cladding), H- (Rubber Jacket), V-(Polyvinyl Chloride ...
	Rittal cabinets – Q&A on the basics of high and low voltage distribution cabinets What are the basic requirements for a high-voltage circuit breaker? A: A. Reliable work; B. Have sufficient circuit breaking capacity C. Have the shortest possible cut-off time; D. Simple structure and low price. What is the purpose of the disconnector? Answer: A. Electrical...
	Rittal cabinets – what are the characteristics of explosion-proof cabinets compared to ordinary cabinets? 1. It can be installed in places where dangerous gases exist, and it is safe to use the control cabinet in some environments with gas or vapor gas. 2. The shell of the control cabinet is generally made of steel plate welding or cast aluminum alloy die-casting, with high-voltage electrostatic spraying, and the whole is made of flameproof type.
	Rittal cabinets – Q&A on the basics of high and low voltage distribution cabinets What is Peak Load? What is trough load? What is Average Load? A: Peak load refers to the maximum load that can occur on the grid and the user in a day. The trough load is the hourly average of the least amount of usage that occurs in the grid and the users in a single day.
	Rittal cabinets – what electrical components are included in the electrical cabinet? 1 Circuit breaker Low-voltage circuit breakers, also known as automatic air switches, can be switched on and off manually, and can be used to distribute electrical energy, start asynchronous motors infrequently, and protect power lines and motors. In the event of a severe overload, short circuit, or undervoltage fault, the circuit can be automatically shut down. 2 Contactors ...
	Some advantages of the Rittal compact AE enclosure The Rittal compact AE cabinet with its new internal expansion rails –Supplementary internal expansion for machining – Can be done in a time-saving manner in the side, bottom and top cover areas Installation – Two rows of adjustable TS 8 system holes for installation capacity Outer space...
	Rittal Nonwovens filter mats product description Product Introduction Product name: Rittal Rittal Product Type: Rittal Non Woven Filter Mats Product Model: 3172.105 Spare filter mats for top-mounted fans, filter fans or thermoelectric coolers to protect control cabinet components from dirt, ash ...
	Rittal cables – the basic structure of industrial control cables 1. Conductor It is the main component of the product to play its use function, and it is to transmit electricity or information, that is, to transmit electric current or electromagnetic waves on the conductor. The conductor is the basic and indispensable main component of the product for the transmission of electric current or electromagnetic wave information. 2. Insulation ...
	Rittal Cables – the operation of power cable routes The operating voltage of the cable Generally speaking, there is a certain relationship between the operating voltage of the cable and the rated voltage. If some cable lines are not in use, they must be connected to the power grid to ensure that the cable lines are not exposed to moisture. When the neutral point is not grounded ...
	Rittal Cables – precautions for the installation and wiring of control cables Precautions for the installation and wiring of control cables: 1. Under the eaves. Cables can only be used if they are not directly exposed to sunlight or ultra-high temperatures, and it is recommended to use pipes. Ultraviolet (UV) – Do not apply cables without UV protection to direct sunlight rings ...
	What is the difference between a control cabinet and a distribution box? One. The nature is different Distribution box: There is a large amount of parameter data in the distribution box. It generally constitutes a low-voltage distribution box. Control cabinet: The control cabinet is to assemble the switch cabinet, measuring instruments, protection devices and auxiliary equipment in a closed or semi-enclosed metal cabinet or screen according to the requirements of electrical wiring.
	What is the daily maintenance method of the air conditioner? - Rittal air conditioning 1. Filter maintenance of the indoor unit: The filter screen of the indoor unit generally needs to be replaced once every two months. It is not recommended to continue to use it after rinsing, because the rinsed filter is easy to stick, so that ventilation and ventilation are not smooth, and air circulation is affected. So if it's a one-off, direct replacement, not ...
	Rittal cabinet air conditioner fault code The fault codes for Rittal cabinet air conditioners are: F1, F2, F3, FF, EH, EP, EL, SF, HC. F1, F2, F3 represent improper use or failure of internal components; FF stands for Regulation Circuit Fault; EH stands for High Temperature Fault; EP stands for Actuator Failure; ...
	For the first time, the Rittal Rittal and Circle B and Switch data centres have launched the European OCP Experience Centre Circle B, Rittal and Switch data centres in Germany launch the first European Open Computing Project (OCP) Experience Centre. The full-featured OCP environment is located at one of the facilities of three switching data centers in the Amsterdam area. (The OCP Experience Center can be used as a demo center, but it is also ...
	Rittal cabinets – Q&A on the basics of high and low voltage distribution cabinets What are the main technical parameters of the fuse? Answer: A. Rated voltage, B. Rated current, C. Breaking capacity, D. Melting characteristics, E. Overvoltage. What are the main products of low-voltage power distribution equipment? Answer: Low-voltage distribution panels, switch cabinets, switch boards, lighting boxes, power boxes and electrical ...