Xinjie inverter control motor method

1. Air opening: a total air switch, which is the power control of the entire cabinet. I believe that every cabinet must have one thing. 2. PLC: This should be selected according to the needs of the project. For example, if the project is small, it can be an integrated PLC, but if the project is more ...

1. Hardware purchase At present, there are a large number of PLC products on the market, more and more cost-effective, and the optional fields are getting bigger and bigger. 1. At the beginning of the scale of the system, it should be determined that the system is a single PLC machine.

Because the current at the input and output ends of the inverter contains high-frequency components, the leakage current formed by the high-frequency components when the inverter is driven is greater than that when the grid power supply is supplied. Because there are many varieties of circuit breakers, in some cases, even the inverter wires and motors ...

The suffix is XT and only supports RS232 communication, 4 inches out. The suffix MT supports RS 232/485/422 communication. The suffix is UT on the basis of MT, and a U disk port is added, which can be used to import and export engineering and CSV data from U disk. The suffix is named ET and is added to the UT ...

The XC series includes XC1 (Economy), XC2 (Basic), XC3 (Standard), XC5 (Enhanced), XCM (Sport), XCC (High Performance) and their corresponding expansion modules. XC series PLC can be ...

Of course, PLC control is much more reliable than relay control, but if the device does not meet the requirements, it will not work. Therefore, the PLC machine should be installed correctly outside. (1) Pay attention to the environment of the installation The temperature should not be lower than 0°C and above 55°C, for example, not installed by a large stove, and ...

Because the current at the input and output ends of the inverter contains high-frequency components, the leakage current formed by the high-frequency components when the inverter is driven is greater than that when the grid power supply is supplied. Because there are many varieties of circuit breakers, in some cases, even the inverter wires and motors ...

A：a. Now only the TGM series touchscreen supports penetration as well as network connectivity b. At present, the penetration function only supports the PLC class of Xinjie that supports the Xnet protocol, and other models do not support it temporarily c. Check whether the computer has the latest version of config installed serial port equipment tool (soft ...

In order to shorten the early problem period, further extend the random problem period, and postpone the arrival of the wear and tear problem period, we will generally choose the method to take a certain approach at the beginning of the system planning.

On March 19, 2021, the "Made in China Digital Service Summit 2021 CAIMRS and Annual Selection and Award Ceremony" held by China's industrial control network was broadcast live on the cloud of the "Industrial Control Network Digital Conference Hall". At the meeting, Pan Yingzhang, President of Gongkong®, officially released China's automation and digital ...

(1) There is no need to adjust the parameters, we can maintain the original parameters (default value) when the inverter leaves the factory. (2) It is the parameter that needs to be set and changed before the trial operation. (3) It is a parameter that is adjusted in the operation of the demand. Frequency converters ...

The output voltage of low-voltage general frequency conversion is 380-650V, the output power is 0.75-400kW, and the working frequency is 0-400Hz. Its control methods have gone through the following four generations. 1U/f=C Sine Pulse Width Modulation (SPWM) Control Method ...

The damage of the inverter to the motor contains two aspects, the damage of the stator winding and the damage of the bearing, this damage usually occurs in a few weeks to more than ten months, the detailed moment and the inverter brand, the motor brand, the motor power, the inverter carrier frequency, the cable length between the inverter and the motor, the ring ...

1. The cause of the leakage problem Some sites use frequency converters to control the motor, which will present the problem of leakage, and the leakage voltage ranges from tens of volts to 200 volts. In view of this problem, the reason for this problem is explained and stated as follows. Depend on...

1. Common problem phenomena When the RS-485 port of the PLC is connected to the computer through the non-blocking PC/PPI cable, the connection between the PLC and the PLC, or the communication between the PLC and the inverter, touch screen, etc., the communication port is damaged, and the more common damage conditions are as follows: (1) R1 or R2 is burned ...

In the instruction manual of the inverter, there is a column that discusses in detail the fault code display of the inverter. 　　1. Short-circuit maintenanceIf there is short-circuit maintenance on the side of the inverter's operation, "0" means that the inverter has short-circuit elements inside or outside. There are several reasons for this ...

Mark point, also known as reference point, provides measurable points for all processes in the surface mount process to ensure the final positioning accuracy.

1) Investigation and investigation of problem phenomena. There are many kinds of inverter problem phenomena, for example, the same type of problem may have different problem phenomena, and different types of problems may have the same problem phenomenon, which brings difficulties to find the problem. However, the problem phenomenon is the basic basis for overhauling the inverter ...

Small PLC manufacturers introduce that PLC products have a wide variety of products, and the specifications and performance are also different. The classification of PLCs is usually based on their structure, function and number of I/O points. 1. Classified by input/output points (1) ...

W-BOX is a 2.4GHzWifi-based wireless communication module independently developed and recently launched by Xinjie in line with the trend of wireless communication. W-BOX can be connected with wireless AP (hotspot) in various occasions to complete long-distance monitoring of PLC and overall control of PLC wireless networking in various environments.