Common problems and solutions of Xinjie PLC

1. On the premise of satisfying the production equipment and process requirements, the acceleration or deceleration time should be increased as much as possible, and then the overcurrent generation in the process of acceleration or deceleration can be avoided. 2. Check whether the inverter, motor, and production equipment are well matched, whether the transmission part is sensitive, and whether the material is ...

Communication: (1) Radiation disturbance; (2) Conduction disturbance Anti-disturbing method: Regarding the disturbance signal transmitted by the radiation method, it is mainly weakened by wiring and shielding the radioactive source and the disturbed line. With regard to the disturbance signal transmitted through the line, ...

Product Description: According to the 2.4GHz Wifi wireless communication module, it has RS232 and RS485 interfaces Compatible with Xinjie XC2 - XCM series, XD series PLC, MODBUS RTU equipment The XD-WBOX-ED is connected to the left side of the XD series PLC Opt IEEE802.11b.g. ...

Xinjie XDM series PLC, XDM is the sports control PLC in the XD series, now has the following types: XDM-24T4-E/C, XDM-32T4-E/C, XDM-60T4-E/C, XDM-60T10-E/C. The XDM series has the following ...

As the only domestic brand among the top 10 small PLC shopping malls in China, Xinjie has broken through the core shopping malls dominated by international brands for more than ten years, and the unswerving commitment of the leader Li Xin to independent development can be seen. ...

In the process of century industry, the more top-level software and hardware planning for the suspension of frequency conversion skills, first according to the characteristics of traditional air compressor motors, comprehensively analyze the causes of energy consumption and operation characteristics, so as to plan the control of frequency conversion skills speed regulation, air skill tightening, pressure sensing skills improvement, etc.

The MS series of servo motors can be installed in either the horizontal or vertical direction. However, if it is installed incorrectly, or in an unsuitable place, it can shorten the life of the motor or cause unexpected accidents. 　　Storage temperature In the unpowered state ...

The damage of the inverter to the motor contains two aspects, the damage of the stator winding and the damage of the bearing, this damage usually occurs in a few weeks to more than ten months, the detailed moment and the inverter brand, the motor brand, the motor power, the inverter carrier frequency, the cable length between the inverter and the motor, the ring ...

1、CPU。 The CPU of the plc is actually the central processing unit, which can carry out the operation and processing of various data, convert various input signals into input registers, and then carry out logical operations, timing, counting, arithmetic operations, data processing and transmission, communication networking and various operations, ...

(1) What is the current setting value of the thermal relay? The setting current of the thermal relay refers to its action current, that is to say, it is adjusted between 0.95 - 1.05 times of the rated current of the motor being maintained.

1. The speed regulation power is high, which is an efficient speed regulation method. This is because after the frequency change, the motor is still working in close proximity to the synchronous speed, and the rated slip is fundamentally adhered to. It's just that in the frequency conversion equipment system, there will be conversion loss, and because of the influence of higher harmonics, the loss of the motor will increase.

1. Operating temperature. The inverter is a high-power electronic component, which is easily affected by the operating temperature, and the product is generally required to be 0-55 °C, but in order to ensure the safety and reliability of the operation, it should be considered to leave room for use, and it is best to control it below 40 °C. In the control box, the inverter ...

1. Look inside the electrical cabinet, for example, to see if there are small animals and their droppings, and whether there are condensation or water marks. If the dust in the cabinet is large, please clear the external radiator of the inverter. 2. Assuming that the humidity is relatively large, there are condensation or water marks, please open the cabinet door first, ventilate and dehumidify, you can use electric fans, etc.

Control principle: PLC controls the operation of the servo motor by controlling the servo motor. 1. The PLC sends a pulse signal to the servo motor driver, pay attention to the driver. 2. The servo motor drive according to the ...

The problem of the inverter is not only affected by external factors, but also by internal factors. 1. The inverter parameter setting is unreasonable and countermeasures to make the inverter work normally, in addition to the normal equipment, the parameter setting is also very important, if the parameter is not set properly, it will not be able to ...

The suffix is XT and only supports RS232 communication, 4 inches out. The suffix MT supports RS 232/485/422 communication. The suffix is UT on the basis of MT, and a U disk port is added, which can be used to import and export engineering and CSV data from U disk. The suffix is named ET and is added to the UT ...

Because the current at the input and output ends of the inverter contains high-frequency components, the leakage current formed by the high-frequency components when the inverter is driven is greater than that when the grid power supply is supplied. Because there are many varieties of circuit breakers, in some cases, even the inverter wires and motors ...

1. The cause of the leakage problem Some sites use frequency converters to control the motor, which will present the problem of leakage, and the leakage voltage ranges from tens of volts to 200 volts. In view of this problem, the reason for this problem is explained and stated as follows. Depend on...

1. For the switching input and output circuits, pay attention to the consistency criterion of maintaining the situation; The positive logic criterion is usually used, that is, when the input and output are live, it is the "ON" state and the data value is "1"; On the other hand, when the input and output are powered off, it is in the "OFF" state and the data value is "0". Such...

There are a variety of harmonic sources in the power system, and the harmonic source is the electrical equipment that injects harmonic current into the shared power grid or generates harmonic voltage in the shared power grid, and the most harmonic source is the converter equipment and other equipment. Harmonic...