Turck's temperature sensor is selected

Choose a modular principle instead of a static line Turck's compact IP67 marginal controllers or block I/O modules enable distributed control of logistics plant processes. These autonomous modules can be used via Profinet, Ethernet/IP or Modbus TCP with multiprotocol Ethernet ...

1. Recognize the type of pressure sensor (1) Electromechanical: The internal mechanical structure of the product, the pressure sensor made of springs, levers, dispatching screws, metal housings, etc., and contact module equipment, does not contain processing circuits inside, and the output is the pressure switch side of the switching quantity.

Assuming that the power supply is normal, it is necessary to carry out simple pressurization to see if the output has changed, perhaps to observe whether the zero position of the sensor has output, assuming that it has not changed, the sensor has been damaged, and vice versa, it is the appearance of the damage or other links of the whole system. ...

Turck's rugged and intuitive PS+ series represents the next generation of fluid sensor technology Turck is launching the new PS+ series of pressure sensors at the Hannover Messe. The series is modular ...

** is the pressure, the transmitter can't lose it. In this case, look at the pressure connector to see if it leaks or is clogged, if it admits not, look at the wiring and see if the power supply is normal, simple pressure to determine if the output has changed, or if there is an output at the zero point of the sensor, ...

1. Types of light sensors 1. Ambient Light Sensor XJC-S05-T New Jingcheng Sensor 503 Series HubaControl Fuba WTAL121-N30LMWoosen WSPSS15B20GTWang Sensor Jude Life CS20D, e.g. sensor on mobile phone on laptop etc.

1. Composition of the sensor A sensor typically consists of a sensitive element, a conversion element, and a basic conversion circuit, as shown in Figure 1. A sensitive element is an element that can sensitively feel the scene being measured and respond to a definite relationship; The conversion element is to convert the measured touch of the sensitive element into ...

1. Attenuation of detection distance. The slip warp is made of iron, which is suitable for inductive sensor detection; The scale of the measured part of the slippery warp is slightly smaller than the scale of the standard test object, so there will be a certain attenuation. 2. On-site anti-disturbance ...

(1) Resistance shunt: practice is a resistance with a very small resistance value, when there is a current through, according to Ohm's law, the voltage occurs in the resistance, and the current is known according to the measured voltage value. The resistor shunt has high precision, fast response speed, low cost, simple use, defects, etc.

The attack of the epidemic in 2020 has made more and more manufacturing enterprises realize the importance of industrial automation transformation and upgrading. In order to help more manufacturing users to develop smartly, Turck has also restarted the 4th National Factory Digitalization Solutions Tour. ...

1. According to the measurement target and measurement environment In order to carry out a detailed measurement work, it is necessary to first consider the principle of the sensor to choose, which needs to be analyzed and many elements can be confirmed. Because, even if the same physical quantity is measured, there are sensors with multiple principles to choose from.

Turck's UNT products detect the orientation of pistons in all standard cylinders, replace most T-slot magnetic sensors on the market today, and can be installed on other cylinder shapes with a wide range of device attachments. It has a compact and compact form factor, which allows it to be fitted ...

Sensitive components Load cell: A component that directly senses the measured (mass) and outputs other quantities that are definitely related to the measured amount. For example, the elastomer of the resistance strain gauge load cell is to transform the mass of the measured object into deformation; The elastomer of the capacitive load cell will be tested ...

The absence of impurities is the ultimate goal in all industries. This is especially important in the chemical industry, where important products are often handled. Pipes are particularly susceptible to contamination and fouling, which can ultimately lead to energy loss. Pigging systems are used to prevent corrosion and contamination of pipelines. The pigging pipe is transported through the pipeline ...

Based on the principle of heat exchange, Turck's flow sensors use energy changes to detect wear-free changes in flow velocity, and send an alarm signal through the processing circuit, with LED indicators indicating the flow status: 1. Traffic ...

There is a difference between the two-wire system and the three-wire system of the proximity switch, and the three-wire system proximity switch is divided into NPN type and PNP type, and their wiring is different. The wiring of the two-wire proximity switch is relatively simple, and the proximity switch is connected in series with the load.

Turck's high-frequency RFID/sensor tags are useful for recording and storing measurements such as temperature and pressure, and are also readable without touch. At the same time, according to the different needs of different customers, Turck is able to ...

1. Thermocouple Thermocouples are the most commonly used temperature sensors for temperature measurement. Its main benefits are a wide temperature scale and adaptability to a wide range of atmospheric environments, and it is robust, inexpensive, does not require electricity, and is also the cheapest. A thermocouple consists of two different metal wires connected at one end (metal A and ...

In order to ensure trouble-free testing and reliable inspection results in the manufacturing industry, many processes require the same inflow and outflow of liquid or gaseous media. In the automated production process, in addition to the pressure sensor and temperature, the measurement of flow rate is also very important. Based on the continuous ...

An example of Turck's debugging method for turck pressure sensors is as follows: Select a 0.08-2MPa planned controller, request the pressure to be reduced to 0.8MPa (down switching value) to announce the contact signal, and the operation process is as follows: ​ Screw the product into the hydraulic pressure ...