Weiluntong touch screen MT (iP) series (compact type)

1. MT200, this model can be said to be the earliest model of this brand, which is very popular in some regions and can realize automated procedures. Second, MT500, this model is the successor of the previous model, after the launch of the very good sales results. ...

To change the IP address of the touchscreen, you need to click the arrow below the touchscreen. Then enter the original password of the touch screen in the pop-up interface: 111111. After that, enter the IP setting interface. Enter the interface to set the IP address you want to set, and finally remember to click after setting ...

1. The power cord is not properly connected This may seem obvious, but make sure the power cord is connected to the back of the touchscreen and plugged into a power outlet. If it looks like it's connected correctly, disconnect and reconnect both ends of the power cord to make sure the cable isn't loose. 2. The power cord is damaged ...

Open the created Weilun touch screen project, select [Common] in the menu bar and click Open. In the Common drop-down menu, select the Bit Status Indicator icon and click Open. In the pop-up [New Bit Status Indicator] setting window [General Properties] ...

Virtual serial port configuration process: 1. Open the virtual serial port configuration software and create two pairs of serial ports; 2. The circle is the physical serial port in the computer, and the virtual serial port in the box; 3. Two groups have been added, and friends who want to add port tests can do so in the window on the right.

1. System parameters 1.1 What do the RS485 2W and RS485 4W in the communication port type mean? RS485 2W represents the wiring method, that is, the two-wire system, that is, there are two signal lines to be connected in addition to GND; RS485 4W represents the wiring method, that is, the four-wire ...

When the HMI communication failure is caused by on-site interference, the following methods can be used to troubleshoot the fault: The communication line adopts shielded twisted pair cable, and the shielding layer needs to be grounded at one end, that is, only one end of the PLC and the touch screen can connect the shielding layer to the ground horn (it is recommended to connect it to the HMI end of the touch screen) ...

Touch screen mobile phone capacitive touch screen and resistive touch screen are mainly different in touch sensitivity, accuracy, cost, multi-touch feasibility, damage resistance, cleaning, and sunlight visual effect. Touch sensitivity, 1. Resistive touch screen: pressure is needed to make all layers of the screen ...

Due to technical limitations and poor environmental adaptability, especially the surface acoustic wave screen, the screen will not be able to be used normally due to water droplets, dust and other pollution, so the Weilun touch screen also needs regular maintenance like ordinary machines. And because the Weilun touch screen is a variety of electrical equipment...

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

30. Button control indicator (same address) Set the multi-state transfer switch element/bit state transfer switch element and the multi-state indicator element/bit status indicator element to the same address, click the multi-state transfer switch element/bit state transfer switch element, and the corresponding indicator ...

1. The line interface of the Weilun Tong touch screen is faulty. 2. Whether there is a crack fault on the surface of the touch screen. 3. External interference and control box failure. 4. The connection between the touch screen and the host or the host is faulty. ...

Merit: 1. The resistive touch screen has high accuracy, which can be at the level of pixels, and the maximum resolution can be up to 4096x4096. 2. The screen is not affected by dust, water vapor and oil, and can be used in a lower or higher temperature environment. 3. Resistive contact ...

The human-machine interface is not just a simple operation screen, but more and more integrated into new functional elements such as network technology, remote control, video input, etc., and has gradually evolved into a networked information control platform integrating display, monitoring, communication and operation. And in this wave of innovation ...

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

Check whether the connection interface is loose, and then check whether Serial Port and Interrupt Number conflict. If there is a conflict, adjust the resources to avoid the conflict. Then check the surface of the touch screen for cracks. If there is a crack, replace it in time. It is also necessary to check the touch screen table ...

1. Click the left arrow in the lower right corner of the screen - gear - enter 6 1s - network; 2. Settings under network: (1) Select IP address get from below (2) Fill in the IP address of the touch screen in the "IP address", for example, set it to 1 ...

1. First of all, open the created Weilun touch screen project, select Common in the menu bar and click Open. 2. Secondly, select the system parameter icon in the common drop-down menu and click to open. 3. Finally, click Change. ...

1、eMT3120A 12.1" TFT display 1024*768 dots, brightness 500, contrast ratio 700:1, 16.2M color, 256MB memory, DC19.2-28.8VDC power supply, four-wire resistive, SD card slot, support SD/SDHC, USB Host USB 2.0 ...

1) Check if the hard drive is turned off in the "Display Energy Saving Settings" of Wlndows 9x. The way to do this is to right-click on the desktop, select the "Properties" command, then select the "Screen Saver" tab from the dialog box, click the "Settings" button, and set the parameter to "...