Megmeet drives – the replacement steps for high-voltage drive power units

1. Check the surrounding situation - carefully check the ventilation and lighting of the inverter and the surrounding environment. It is necessary to ensure that the ventilation equipment is functioning properly and that the lighting equipment is in working order. 2. Check the internal cable - open the inverter cabinet door and check whether the internal cable is damaged, the cable ...

1. External equipment failure. Such faults come from external devices such as various sensors, switches, actuators, and loads. The failure of this part of the equipment will directly affect the control function of the system. This type of failure is usually caused by the quality and longevity of the equipment itself. 2. System failure ...

1. E1: indicates sensor failure. In this case, it is necessary to check whether the sensors of Megmeet are damaged or whether the wiring is loose. 2. E2: Indicates overweight load. At this point, it is necessary to check whether the load of Megmeet exceeds the set maximum load. 3. E3: Indicates battery ...

1. Intelligent network The intelligent inverter does not need to set a lot of parameters when it is used, and it has the function of fault self-diagnosis, which has high stability, high reliability and practicability. The Internet can be used to realize the linkage of multiple inverters, and even the inverter complex in the factory.

In the manufacturing industry, there are a large number of open-loop sequential control based on switching quantities, which carries out sequential action numbers according to logical conditions and operates in chronological order; In addition, there is the control of chain protection actions according to the logical relationship that is not related to the sequence and timing; As well as a large number of switching quantities, pulse quantities, gauges...

The inverter should be installed inside the control cabinet, and the design of the control cabinet should pay attention to the following issues: 1. Wiring specification of inverter The signal line and the power line must be separated: When using an analog signal to remotely control the inverter, in order to reduce the interference of the analog signal to equipment such as the inverter, ...

The high-voltage inverter has a highly intelligent computing level and a perfect fault detection circuit, and can provide accurate positioning of all faults, and make clear instructions on the main control interface. In practical application, we find that common faults can be divided into abnormal control channels, IGBT overcurrent, overvoltage...

The first is that the PLC sends a start/stop signal to the server through the I/O point, and the server controls the operation of the servo motor. The PLC controls the operation/stop of the servo through the digital output, so as to achieve the purpose of controlling the servo motor. The second is through the pulse output of the PLC, which ...

1. Common processing: reset the monitoring timer, perform hardware checks, user memory checks, etc. 2. Program execution: The CPU interprets and executes each instruction in the order of first left and then right, first up and then down, and reads out each relay according to the input image register and the component image register.

Inverter energy saving The energy saving of the inverter is mainly manifested in the application of fans and pumps. In order to ensure the reliability of production, all kinds of production machinery are designed with power drive, and there is a certain amount of surplus. When the motor cannot operate at full load, in addition to meeting the power drive requirements, ...

External electromagnetic interference can easily cause malfunctions If there are interference sources around the inverter, they will invade the inside of the inverter through radiation or power lines, causing the control loop to malfunction, causing abnormal operation or shutdown, and even damage to the inverter in severe cases. Noise suppression on the outside ...

1. Regularly dust the inverter, focusing on the rectifier cabinet, inverter cabinet and control cabinet, if necessary, the rectifier module, inverter module and the circuit board in the control cabinet can be removed for dust removal. Whether the lower air inlet and upper air outlet of the inverter are dusty or blocked due to excessive dust. The inverter is due to the ...

1. Correctness (low debugging cost) First of all, the PLC program must be able to work correctly to meet the requirements of the actual control process. This is the essence of the PLC program, and if you don't do that, nothing else makes sense. 2. Reliability (low maintenance cost) Not only to ...

First, some problems in the application of frequency converter 1.1 Harmonic problems The devices that play a switching role in the main circuit of the inverter must generate harmonics in the process of turning on and off the circuit. The lower harmonics usually have a greater impact on the motor load, causing torque ripple; And the higher ...

Safety operation procedures for spot welding machines: 1. Before operation, the oil stain of the upper and lower electrodes should be removed. After power-on, the body shell should be free of leakage. 2. Before starting, the steering switch of the control line and the small switch of welding current should be connected, the number of poles should be adjusted, and then the water source and gas source should be connected.

1. Intelligent network The intelligent inverter does not need to set a lot of parameters when it is used, and it has the function of fault self-diagnosis, which has high stability, high reliability and practicability. The Internet can be used to realize the linkage of multiple inverters, and even the inverter complex in the factory.

(1) The energy density is highly concentrated, the heating and cooling speed is extremely fast during welding, the heat affected zone is small, and the welding stress and deformation are very small; (2) Non-touch processing, no external force on the weldment, suitable for welding parts that are difficult to touch; (3) The laser can be transmitted through the optical incoming ...

1. PLC is a relatively mature control system composed of single-chip microcomputer, which is the product of a mature and stable single-chip microcomputer application system that has been debugged. It is highly versatile. 2. The single-chip microcomputer can form a variety of application systems, and the application range is wider. In the case of a single "microcontroller", it ...

(1) Use the analog output module of PLC to control the analog output module of the inverter The analog output module of the PLC outputs 0-5V voltage signal or 4-20mA current signal, which is used as the analog input signal of the inverter to control the output frequency of the inverter. This control method is simple to wiring, but it needs to be selected and changed.

1. After connecting the wires according to the wiring diagram, start the power supply and prepare to set the parameters of the inverter. 2. Press the "MODE" button to enter the parameter setting mode, and set the Pr.79 to "2": external operation mode, the start signal is input by the external terminal (STF, STR), and the speed adjustment is carried out by the external terminal.