Banner Sensors – Applications for Fiber Optic Displacement Sensors

(1) The sensing element in the distributed optical fiber sensing system is only optical fiber; (2) The one-dimensional distribution map to be measured in the whole optical fiber area can be obtained in one measurement, and the two-dimensional and three-dimensional distribution of the measured can be determined by erecting the optical fiber into a grating shape; (3) The empty ...

1. Optical adjustment The factory setting of the sensor is a large range, and this setting is subject to change. Note: Only use your finger to press the button. 2. Set the range (when stationary) 1. Adjust the sensor with a reflector; 2. Press the button for about 3s until two ...

1. Photoelectric head dust masking When the photoelectric sensor is operating, it is easy to accumulate dust or oil dirt on the receiving head, resulting in problems such as insensitive sensor response, false triggering or non-triggering, and even failure to operate normally. At this time, we need to clean the photoelectric head. Cleaning method: ...

The linear line works on the same principle as a sliding rheostat and is used as a voltage divider, which represents the actual position of the measured position with a relative output voltage. There are the following requirements for the work of this device: 1. If the electronic ruler has been used for a long time ...

1. The use of ultrasonic spacer sensor skills An ultrasonic sensor consists of three parts: an ultrasonic transducer, a processing unit, and an output stage. First, the processing unit excites the ultrasonic transducer with voltage, and after it is excited, it announces the ultrasonic wave in the form of pulses, and then the ultrasonic transducer is transferred to withstand ...

(1) When the target to be measured is not perpendicular to the transducer of the sensor. This is because the target of the ultrasonic test must be within an angle of no more than 10° perpendicular to the sensor. (2) When a small beam diameter is required. Because the diameter of the general ultrasonic beam is ...

Active infrared sensor The transmitter of the active infrared sensor emits a modulated infrared beam, which is received by the infrared receiver, thus forming a cordon composed of infrared beams. When encountering leaves, rain, small animals, snow, dust, fog obstruction, should not call the police, people or quite ...

1. Prevent the debris from being deposited in the catheter and the sensor from coming into contact with corrosive or overheated media. 2. When measuring gas pressure, the pressure intake should be opened at the top of the process pipeline, and the sensor should also be installed in the upper part of the process pipeline, so that the accumulated liquid can be easily injected into the process pipeline. ...

(1) The Ultimate Problem Solver: Solve the most challenging applications by reducing sensor inventory with reliable, durable sensors (2) Regardless of the reflectivity of the target surface, the solution is difficult distance-based applications, including black foam on black plastic, black rubber in front of metal, multi-packing, etc.

(1) When the grating ruler displacement sensor is connected to the digital display table, the power must be cut off, and the power supply will be provided after the plug is linked. (2) The grating ruler displacement sensor should prevent foreign objects from entering its interior, including water, oil, dust, etc., so a protective cover should be installed as much as possible outside. (3) Periodic inspection ...

1. Red LED – visible light, easy to adjust. 2. Infrared LED – high energy invisible light. 3. Red laser – visible light, its physical properties are ideal for small object detection and large detection ranges. ...

1. Correct installation method of pressure sensor: (1) Verify the frequency response value of the pressure sensor under normal atmospheric pressure and standard temperature conditions with appropriate instruments. (2) Verify the correctness of the code of the pressure sensor and the corresponding frequency response signal. 2. ...

The common faults of Banner displacement sensors are described in seven points, the details are as follows: 　　The linear line works on the same principle as a sliding rheostat and is used as a voltage divider, which represents the actual position of the measured position with a relative output voltage. To this outfit ...

1. Intensity-modulated optical fiber sensor It is a sensor that uses changes in the refractive index, absorption, or reflection of sensitive components caused by changes in the parameters of the measured object to achieve sensitive measurements. There are microbending losses using optical fibers; absorption characteristics of each substance; Raise...

(1) The principle of physical optical fiber sensor, which uses the sensitivity of optical fiber to environmental changes to convert the input physical quantity into a modulated optical signal. Its working principle is based on the optical modulation effect of optical fibers, that is, the optical fiber's response to external environmental factors, such as temperature, pressure, electric field, ...

1. Add a protective cover as much as possible, and clean up the chips and oil splashed on the ruler in time to strictly prevent any foreign matter from entering the inside of the grating ruler sensor housing. 2. When plugging and unplugging the grating displacement sensor and the plug holder of the digital display, the power should be turned off. 3. For the extension of the dust seal ...

1. Use the 4 fixing screw holes at the bottom to install directly or add protection or other mechanical use according to the needs of the site and machine installation space facilities. 2. When installing the stainless steel cable, it is necessary to pay attention to the horizontal angle, that is, to make the mechanism of the steel cable from the outlet to the moving part as much as possible, and slide horizontally during work.

Photoelectric sensors Ordinary detection Groove detection Fiber inspection Laser detection Ambient light source detection Photoelectric buttons Measurement and inspection products Color code and color detection C-GAGE Optical measurement of L-GAGE Ultrasonic measurement ...

(1) Measurement of absolute air pressure by electronic means makes the control of the inflatable state of the line more complete and continuous. (2) From the dynamic and static aspects, the air leakage point can be estimated in advance. (3) Determine the change in time of the pressure inside the cable, so that the inflatable ...

Everyone is familiar with the brand Banner, what are the fields of sensor applications under Banner? Today, we will introduce the application fields of Banner sensors, which are mainly used in: booster cylinders, boosters, gas-hydraulic booster cylinders, gas-liquid boosters, presses, compressors, air conditioning and refrigeration equipment, etc.