The linear line works on the same principle as a sliding rheostat and is used as a voltage divider, which represents the actual position of the measured position with a relative output voltage. There are the following requirements for the work of this device:
1. If the electronic ruler has been used for a long time, and the seal has been aged, and there are many impurities mixed with it, and the water mixture and oil will seriously affect the contact resistance of the brush, which will make the displayed numbers keep jumping. At this time, it can be said that the electronic ruler of the linear displacement sensor has been damaged and needs to be replaced.
2. If the capacity of the power supply is very small, there will be many situations, so the power supply needs to have sufficient capacity. Then, if the capacity is insufficient, it will cause the following situation: the movement of the melt will cause the display of the clamping electronic ruler to change and fluctuate, or the movement of the clamping will cause the display of the injection electronic ruler to fluctuate, resulting in a large error in the measurement results. If the driving power supply of the solenoid valve is at the same time as the power supply of the linear displacement sensor, the above situation is more likely to occur, and the voltage level of the multimeter can even be measured with the voltage level of the multimeter in serious cases. If the situation is not caused by high-frequency interference, electrostatic interference, or neutralization is not good enough, then it is possible that the power supply is too small.
3. Frequency modulation interference and electrostatic interference may make the display number of the electronic ruler of the linear displacement sensor jump. The signal line of the electronic ruler and the strong current line of the equipment should be separated from the wiring slot. The use of grounding brackets must be mandatory, and at the same time, the housing of the electronic ruler must be in good contact with the ground. The signal wire needs to be shielded, and a section of the electrical box should be grounded with the shielded wire.
If there is high-frequency interference, the voltage measurement using the multimeter will usually show normal, but the display number will jump non-stop; In the case of electrostatic interference, the situation is the same as that of high-frequency interference. To prove whether it is electrostatic interference, you can first use a section of power cord to connect the cover screw of the electronic ruler with some metal on the machine, as long as it is short-connected, the electrostatic interference will be eliminated immediately. However, if you want to eliminate high-frequency interference, it is difficult to use the above method, and high-frequency interference often occurs in frequency converter savers and manipulators, so you can try to use the method of stopping high-frequency power savers or manipulators to verify whether it is high-frequency interference.
4. If the electronic ruler of the linear displacement sensor is in the process of working, the display data at a certain point beats regularly, or there is no display data, in this case, it is necessary to check whether the insulation of the connecting wire is damaged, and the short circuit to the ground caused by regular contact with the shell of the machine.
5. The voltage of the power supply must be stable, and the industrial voltage needs to meet the stability of ±0.1 [%], for example, if the reference voltage is 10V, it can allow a fluctuation of ± 0.01V, if not, it will cause the fluctuation of the displayed trap. However, if the amplitude of the fluctuation of the display at this time does not exceed the amplitude of the fluctuation of the fluctuating voltage, then the electronic ruler is normal.
6. The alignment of the linear displacement sensor needs to be very good, but the parallelism can be allowed to have an error of ±0.5mm, and the angle can be allowed to have an error of ±12°. However, if the parallelism error and angle error are large, the display number will jump. In such a situation, the parallelism and angle must be adjusted.
7. In the process of connection, we must pay more attention to the fact that the three wires of the electronic ruler cannot be connected wrong, and the power line and output line cannot be replaced. If the above line is wrong, there will be a large linearity error, it is difficult to control, the accuracy of the control will become very poor, and the display is easy to jump and so on.
|
More on that
|
Banner Sensors - Introduction to the applications and characteristics of various types of sensors
1. Resistive type
A resistive sensor is a device that converts measured physical quantities such as displacement, deformation, force, acceleration, humidity, temperature, etc. into resistance values. There are mainly resistive strain, piezoresistive, thermal resistance, thermal, gas-sensitive, moisture-sensitive and other resistive sensing.
|
|
What problems do Banner laser distance sensors have that need to be solved?
(1) When the target to be measured is not perpendicular to the transducer of the sensor. This is because the target of the ultrasonic test must be within an angle of no more than 10° perpendicular to the sensor.
(2) When a small beam diameter is required. Because the diameter of the general ultrasonic beam is ...
|
|
Banner Sensor - Common fault phenomena and judgment methods of fiber optic sensors
1. There is no display on the digital display after connecting the power supply
(1) Check whether the power cord is broken and whether the plug contact is good.
(2) Whether the power fuse of the digital display meter is blown.
(3) Whether the power supply voltage meets the requirements.
2. The digital display table does not count
(1) Passing ...
|
|
Banner Sensors – Six Elements of Fiber Optic Sensor Selection
1. Determine the type according to the measurement object and environment
It is necessary to carefully analyze the measurement work and consider which principle of sensor to use for measurement, because even the same physical quantity can be measured by different principles. Secondly, we have to consider the range, volume (whether the space is sufficient), amperemia ...
|
|
Banner Sensors - An introduction to the classification of fiber optic sensors
According to the modulation form of the light measured object, it can be divided into: intensity modulation type, polarization state type, phase type and frequency type;
According to whether the light interferes or not, it can be divided into: interference type and non-interference type;
Depending on whether it is possible to continuously monitor the measured as the distance increases, it can be divided into ...
|
|
Banner Sensors – Pressure Sensors are used in applications
Pressure sensors are mainly used in: booster cylinders, boosters, gas-liquid booster cylinders, gas-liquid boosters, presses, compressors, air conditioning and refrigeration equipment and other fields.
1. It is applied to hydraulic system
The pressure sensor is mainly used to complete the closed-loop control of the force in the hydraulic system. When the control ...
|
|
Banner Sensors – Where can fiber optic sensors be used?
Insulated from dirt, magnetic, sound, pressure, temperature, acceleration, gyroscope, displacement, liquid level, torque, photoacoustics, current, fiber optic sensors can be used for displacement, vibration, rotation, pressure, bending, strain, velocity, acceleration, current, magnetic field, voltage, humidity, temperature, sound field, current...
|
|
Banner Sensor - How and how to select a proximity sensor
A proximity sensor is a device with the ability to perceive the proximity of an object, which uses the sensitivity of the displacement sensor to the approaching object to identify the proximity of the object and output the corresponding switching signal. For this reason, proximity sensors are often referred to as proximity switches. It is an alternative to contact detection ...
|
|
Banner Sensors – Rope Position Sensor Installation Considerations
1. Use the 4 fixing screw holes at the bottom to install directly or add protection or other mechanical use according to the needs of the site and machine installation space facilities.
2. When installing the stainless steel cable, it is necessary to pay attention to the horizontal angle, that is, to make the mechanism of the steel cable from the outlet to the moving part as much as possible, and slide horizontally during work.
|
|
Banner Engineering QCM series color sensor features introduced
The QCM series reliably detects distances within a measuring range
A single sensor can distinguish up to 12 colors, saving inventory costs
The anti-glare version reliably detects highly reflective objects
The sensor has an integrated display as well as buttons for intuitive ...
|
|
Banner Sensors – What can ultrasonic sensors be used for?
1. The use of ultrasonic spacer sensor skills
An ultrasonic sensor consists of three parts: an ultrasonic transducer, a processing unit, and an output stage. First, the processing unit excites the ultrasonic transducer with voltage, and after it is excited, it announces the ultrasonic wave in the form of pulses, and then the ultrasonic transducer is transferred to withstand ...
|
|
Banner Sensors – Applications for Fiber Optic Displacement Sensors
1. Microwave and RF environments
2. Nuclear energy and hazardous environments
3. High temperature and high pressure environment
4. Online monitoring
5. Aerospace applications
6. Civil engineering and geotechnical applications
7. Materials Science
...
|
|
Banner Sensor - The appearance of a fiber optic sensor
The appearance of a fiber optic sensor is basically made up of the following parts, from left to right:
(1) SET key, which can be used for sensitivity setting. The basic principle of the sensor is to sense the refractive index of different media through an optical fiber probe to obtain a digital signal, which is displayed on the screen.
|
|
Banner Sensors - Precautions for the use of grating rulers, displacement sensors, and electronic rulers
(1) When the grating ruler displacement sensor is connected to the digital display table, the power must be cut off, and the power supply will be provided after the plug is linked.
(2) The grating ruler displacement sensor should prevent foreign objects from entering its interior, including water, oil, dust, etc., so a protective cover should be installed as much as possible outside.
(3) Periodic inspection ...
|
|
Banner Sensor - Introduction to the characteristics of fiber optic pressure sensors
1. High sensitivity,
2. The geometry has multi-faceted adaptability, and can be made into optical fiber sensors of any shape;
3. It can manufacture devices that can sense various different physical information (sound, magnetism, temperature, rotation, etc.).
4. It can be used for high voltage, electrical noise ...
|
|
Banner Sensors – Troubleshooting solutions for pressure sensors
(1) Measurement of absolute air pressure by electronic means makes the control of the inflatable state of the line more complete and continuous.
(2) From the dynamic and static aspects, the air leakage point can be estimated in advance.
(3) Determine the change in time of the pressure inside the cable, so that the inflatable ...
|
|
A brief analysis of the static characteristics of the sensor
The static characteristics of a sensor refer to the performance of the sensor in a static state, which is an important indicator to measure the sensor. The static characteristics of a sensor include linearity, repeatability, hysteresis, accuracy, sensitivity, threshold and resolution, drift, and more.
1. Linearity refers to the sensor measurement ...
|
|
Banner's visual and safety solutions for efficient machine loading
The progress of industrial automation and intellectualization has enabled human beings to gradually liberate themselves from heavy manual labor, and the emergence of machine tools and machining centers has enabled machines to complete the processing of parts faster and more accurately, and the emergence of automatic loading and unloading systems has made the machining center more powerful. And the loading and unloading ...
|
|
Banner Sensors – Causes and solutions for sensors that always alarm
1. The reason for the total alarm of the sensor
The total sensor alarm is when the sensor's alarm indicator is always on, but the sensor is not actually catching the outlier. This can happen for a variety of reasons, but here are some of the most common ones:
1. Sensor device ...
|
|
Banner Sensors – the development trend of smart temperature sensors
The three foundations of modern information technology are information collection (i.e., sensor technology), information transmission (communication technology), and information processing (computer technology). Sensors belong to the cutting-edge products of information technology, especially temperature sensors are widely used in industrial and agricultural production, scientific research and life.
|
|
Contact
working hours
