Banner Sensors – Typical applications for fiber optic sensors

1. Realize the simultaneous measurement of multiple physical parameters (temperature and strain) or chemical parameters on a single optical fiber; 2. Improve the measurement range of the measurement system and reduce the measurement time; 3. Improve the detection ability of the signal receiving and processing system, improve the spatial resolution and measurement of the system.

1. Fully automatic calibration When the workpiece enters the sensitive area of the probe, hold down the "SET" button for 3 seconds, the sensitivity value will be set and displayed in green 2. Two-point calibration When the workpiece is not in the sensitive area, hold down the "SET" key for three seconds, there is a ...

1. Fiber optic gyroscope Fiber optic gyroscopes can be divided into interference type, resonant type and Brillouin type according to the principle, which is the representative of the three generations of fiber optic gyroscopes. The first generation of interferometric fiber optic gyroscopes, which is now mature and suitable for mass production and commercialization; The second generation of resonant fiber optic gyroscopes, ...

The first is that the pressure rises and the transmitter cannot convey. In this case, the first thing to do is to check the pressure connection for air leaks or blockages. If not, check the wiring method and power supply. If the power supply is normal, simply pressurize and see if the output changes, or if the sensor part outputs. As...

Modbus is an application-layer protocol that defines a data unit (ADU) that is independent of the underlying network and can communicate over Ethernet (TCP/IP) or serial links (RS232, RS485, etc.) (Ethernet ADUs and serial ADUs are slightly different). On a serial link, the Modbus protocol has two ...

Superior color contrast sensitivity, detecting contrast as low as 2% over a wide range of colors Excellent performance in low-contrast or high-gloss applications Ultra-fast 10 kHz switching frequency (10,000 starts per second) with 15μs repeatability Robust and durable zinc ...

A proximity sensor is a device with the ability to perceive the proximity of an object, which uses the sensitivity of the displacement sensor to the approaching object to identify the proximity of the object and output the corresponding switching signal. For this reason, proximity sensors are often referred to as proximity switches. It is an alternative to contact detection ...

(1) The Ultimate Problem Solver: Solve the most challenging applications by reducing sensor inventory with reliable, durable sensors (2) Regardless of the reflectivity of the target surface, the solution is difficult distance-based applications, including black foam on black plastic, black rubber in front of metal, multi-packing, etc.

The progress of industrial automation and intellectualization has enabled human beings to gradually liberate themselves from heavy manual labor, and the emergence of machine tools and machining centers has enabled machines to complete the processing of parts faster and more accurately, and the emergence of automatic loading and unloading systems has made the machining center more powerful. And the loading and unloading ...

First, the reason for the alarm code of the pressure sensor There are generally a variety of reasons for the alarm code of a pressure sensor, among which the following conditions are the following: 1. The sensor circuit is short-circuited or broken due to damage or aging of the sensor sensing element, which causes the machine code to send an alarm signal. ...

(1) When the grating ruler displacement sensor is connected to the digital display table, the power must be cut off, and the power supply will be provided after the plug is linked. (2) The grating ruler displacement sensor should prevent foreign objects from entering its interior, including water, oil, dust, etc., so a protective cover should be installed as much as possible outside. (3) Periodic inspection ...

(1) When the target to be measured is not perpendicular to the transducer of the sensor. This is because the target of the ultrasonic test must be within an angle of no more than 10° perpendicular to the sensor. (2) When a small beam diameter is required. Because the diameter of the general ultrasonic beam is ...

1. Non-contact detection, the sensor has a long service life and no damage to the inspected object. 2. It is used for long-distance detection and has a wide range of uses. 3. There are many types of objects to be inspected, including objects that have an impact on light propagation. 4. High response frequency, suitable for high-speed assembly line ...

Analog vs Digital Output: This is the first thing to consider. This depends on the interface between your system and the accelerometer. Generally, the analog output voltage is proportional to the acceleration, for example, 2.5V corresponds to 0g acceleration, and 2.6V corresponds to 0.5g acceleration. ...

1. Adjust the installation position: After the wire is connected and energized, carefully adjust the installation position to make the light point projected on the surface of the measured object the clearest and brightest. 2. In general, turning the sensitivity knob clockwise can make the green light (OUT2) on, and counterclockwise turning the red light (OUT1) on. a. Replace the light point ...

How laser sensors work In the industrial field, the most common laser sensor is the laser displacement sensor, also known as the laser distance sensor, which can accurately measure the position, displacement and other changes of the measured object without contact, and is mainly used to detect the displacement, thickness, vibration, distance of the object.

1. It is necessary to prevent the sensor from engaging with corrosive gases, preventing it from corroding and affecting the effectiveness of measurement. 2. Assuming that the measurement is a high-temperature medium, it is necessary to see whether the temperature is within the appropriate temperature scale of the sensor.

1. For example, if an emergency stop switch is installed on some machines, then when the machine fails or is in danger, we can cut off the power supply and stop the operation of the equipment through the installed emergency stop switch, so as to protect the safety of people and equipment. The emergency stop switch is usually manually controlled ...

peculiarity 1. Because the prism is used in the reflector, its detection performance is higher and more reliable than that of the general reflective light-controlled sensor 2. Compared with the detached photosensor, the circuit connection is simpler and easier. 3. The design of the child and mother buckle is embedded, and the safety ...

1. High precision: Banner metal laser sensors provide up to 0.1 micron accuracy, which can meet the needs of high-precision measurement and control. 2. Long-distance measurement: The laser beam of Banner laser sensor can cover a distance of several hundred meters, which can achieve long-distance measurement. 3. High speed ...