How to maintain Banner sensors after use

There are two measuring principles for fiber optic sensors. (1) The principle of physical optical fiber sensor, which uses the sensitivity of optical fiber to environmental changes to convert the input physical quantity into a modulated optical signal. Its working principle is based on the optical modulation effect of optical fibers, i.e. the optical fiber ...

1. Determine the installation location. Like injection molding machines, hydraulic presses, etc., are generally installed on the front 2 sides, and some non-standard equipment should be determined according to the actual situation to determine the installation position, to achieve the role of protection, without hindering the normal work. 2. Punching. Determine the installation location ...

1. Strain gauge pressure sensor Strain gauge pressure sensors are sensors that measure pressure primarily by measuring the strain of an elastic element. Depending on the material, strain gauges are divided into metals and semiconductors. When the conductor and the semiconductor material are mechanically deformed, their resistance value will change.

1. Improper installation and introduction errors In other words, the thermocouple should not be installed too close to the door and the heating place, and the penetration depth should be at least 8-10 times the diameter of the maintenance tube; Maintenance of thermocouples ...

Modbus is an application-layer protocol that defines a data unit (ADU) that is independent of the underlying network and can communicate over Ethernet (TCP/IP) or serial links (RS232, RS485, etc.) (Ethernet ADUs and serial ADUs are slightly different). On a serial link, the Modbus protocol has two ...

1. Adjust the installation position: After the wire is connected and energized, carefully adjust the installation position to make the light point projected on the surface of the measured object the clearest and brightest. 2. In general, turning the sensitivity knob clockwise can make the green light (OUT2) on, and counterclockwise turning the red light (OUT1) on. a. Replace the light point ...

Pressure is one of the important parameters in industrial production, and in order to ensure the normal operation of production, it must be monitored and controlled. The following are common terms used when selecting pressure sensors: Standard press The magnitude of the pressure expressed by atmospheric pressure is greater than the atmospheric pressure ...

1. Color recognition function 2. Color recognition function independent of working distance 3. It can also provide reliable detection of vibrating objects 4. White LED 5. Dynamic, remote control teaching function 6. Trigger input 7.3 color channels, 5 levels of threshold 8. May ...

1. High precision: Banner metal laser sensors provide up to 0.1 micron accuracy, which can meet the needs of high-precision measurement and control. 2. Long-distance measurement: The laser beam of Banner laser sensor can cover a distance of several hundred meters, which can achieve long-distance measurement. 3. High speed ...

1. It is directly used for the determination of various pressures: air pressure, water pressure, hydraulic pressure (including water pressure), various blood pressure measurements of people in life, etc.; 2. Pressure sensors are used in automobiles, some high-end motorcycles and almost all internal combustion engines; 3. Level gauge: all kinds of liquid level ...

1. Fiber optic gyroscope Fiber optic gyroscopes can be divided into interference type, resonant type and Brillouin type according to the principle, which is the representative of the three generations of fiber optic gyroscopes. The first generation of interferometric fiber optic gyroscopes, which is now mature and suitable for mass production and commercialization; The second generation of resonant fiber optic gyroscopes, ...

When choosing a pressure sensor, we need to consider its comprehensive accuracy, and what are the aspects that affect the accuracy of the pressure sensor? In fact, there are many factors that cause sensor error, and we will pay attention to four unavoidable errors, which are the initial error of the sensor. Head...

Depending on the mode of exercise Linear Position Sensor: The function of a linear displacement sensor is to convert the linear mechanical displacement into an electrical signal. In order to achieve this effect, the variable resistance slide rail is usually fixed on the fixed part of the sensor, and the displacement of the slide on the slide rail is measured.

A proximity sensor is a device with the ability to perceive the proximity of an object, which uses the sensitivity of the displacement sensor to the approaching object to identify the proximity of the object and output the corresponding switching signal. For this reason, proximity sensors are often referred to as proximity switches. It is an alternative to contact detection ...

The QCM series reliably detects distances within a measuring range A single sensor can distinguish up to 12 colors, saving inventory costs The anti-glare version reliably detects highly reflective objects The sensor has an integrated display as well as buttons for intuitive ...

1. Application in industrial automatic detection and automatic control system Sensors play an extremely important role in industrial automation production. In the petroleum, chemical, electric power, steel, machinery and other processing industries, sensors are responsible for detecting various information.

The first point is that photoelectric sensors and fiber optic sensors work differently First of all, from the working principle of the two, first of all, the photoelectric sensor works according to the principle of the photoelectric effect, that is, when the light hits the photoelectric sensor made of semiconductors, it will emit light ...

1. The size of the photoelectric sensor should be in line with its own production environment, and it needs to be measured before selection. 2. Select the sensing mode suitable for the environment and choose it appropriately. 3. The selection of sensing range should be carried out according to the production environment of its own products, regardless of the range ...

1. Optical adjustment The factory setting of the sensor is a large range, and this setting is subject to change. Note: Only use your finger to press the button. 2. Set the range (when stationary) 1. Adjust the sensor with a reflector; 2. Press the button for about 3s until two ...

Cleaner: Clean the surface of the Banner sensor with a special cleaner to remove dirt and dust. Do not use any acidic or alkaline cleaners to avoid damaging the sensor surface. It is recommended to use anhydrous alcohol or deionized water for cleaning. Lube: Some Banner sensors require ...