Introduction to the features of the Banner R58E three-color light source color scale sensor

Banner Engineering Introduces New Q2XAF150 Background Suppression Photoelectric Sensor! Q2X is a compact photoelectric sensor, which enhances the anti-interference ability of energy-saving lamps, and the crosstalk immunity algorithm allows the two sensors to be used at close range, which can accurately and reliably detect the orientation of small parts, which is suitable for ...

The 2018 China Automation Industry Annual Conference and the 13th China Automation Industry Century Tour (CAIAC2018) were held on April 12, 2018 at Tianma Hotel, Shaoxing, Zhejiang. CAIAC2018 aims to remember and look forward to China ...

1. Flange fixed installation Flange mounting is to connect the pressure sensor to the flange and fix the flange to the measured object. The advantage of this installation method is that it is simple in structure, easy to install and disassemble, and suitable for occasions where frequent sensor replacement is required. But...

Cleaner: Clean the surface of the Banner sensor with a special cleaner to remove dirt and dust. Do not use any acidic or alkaline cleaners to avoid damaging the sensor surface. It is recommended to use anhydrous alcohol or deionized water for cleaning. Lube: Some Banner sensors require ...

1. Simple structure: no active electrical contacts, long life. 2. High sensitivity: the output signal is strong, and the voltage sensitivity can reach hundreds of millivolts per millimeter. 3. Large resolution: you can feel the slight mechanical displacement and the slight angle change. 4. Repeatability and linearity ...

Modbus is an application-layer protocol that defines a data unit (ADU) that is independent of the underlying network and can communicate over Ethernet (TCP/IP) or serial links (RS232, RS485, etc.) (Ethernet ADUs and serial ADUs are slightly different). On a serial link, the Modbus protocol has two ...

1. Determine the type according to the measurement object and environment It is necessary to carefully analyze the measurement work and consider which principle of sensor to use for measurement, because even the same physical quantity can be measured by different principles. Secondly, we have to consider the range, volume (whether the space is sufficient), amperemia ...

When choosing a pressure sensor, we need to consider its comprehensive accuracy, and what are the aspects that affect the accuracy of the pressure sensor? In fact, there are many factors that cause sensor error, and we will pay attention to four unavoidable errors, which are the initial error of the sensor. Head...

(1) Measurement of absolute air pressure by electronic means makes the control of the inflatable state of the line more complete and continuous. (2) From the dynamic and static aspects, the air leakage point can be estimated in advance. (3) Determine the change in time of the pressure inside the cable, so that the inflatable ...

1. It is necessary to prevent the sensor from engaging with corrosive gases, preventing it from corroding and affecting the effectiveness of measurement. 2. Assuming that the measurement is a high-temperature medium, it is necessary to see whether the temperature is within the appropriate temperature scale of the sensor.

1. Intensity-modulated optical fiber sensor It is a sensor that uses changes in the refractive index, absorption, or reflection of sensitive components caused by changes in the parameters of the measured object to achieve sensitive measurements. There are microbending losses using optical fibers; absorption characteristics of each substance; Raise...

1. Temperature sensor Temperature sensors are used to detect temperature and heat energy and convert it into an electrical signal (transmitted in the form of voltage or current). We actually have the following types of temperature sensors to use. 1. Thermometer 2. Thermocouples ...

(1) When the grating ruler displacement sensor is connected to the digital display table, the power must be cut off, and the power supply will be provided after the plug is linked. (2) The grating ruler displacement sensor should prevent foreign objects from entering its interior, including water, oil, dust, etc., so a protective cover should be installed as much as possible outside. (3) Periodic inspection ...

1. Fully automatic calibration When the workpiece enters the sensitive area of the probe, hold down the "SET" button for 3 seconds, and the sensitivity value will be set and displayed in green 2. Two-point calibration When the workpiece is not in the sensitive area, hold down the "SET" key for three seconds, there is a ...

1. There is no display on the digital display after connecting the power supply (1) Check whether the power cord is broken and whether the plug contact is good. (2) Whether the power fuse of the digital display meter is blown. (3) Whether the power supply voltage meets the requirements. 2. The digital display table does not count (1) Passing ...

1. Physical sensor: A physical sensor is a sensor that detects a physical quantity. It is a device that uses certain physical effects to convert the measured physical quantity into a signal in the form of energy that can be easily processed. There is a definite relationship between the output signal and the input signal. The main physical ...

The common faults of Banner displacement sensors are described in seven points, the details are as follows: 　　The linear line works on the same principle as a sliding rheostat and is used as a voltage divider, which represents the actual position of the measured position with a relative output voltage. To this outfit ...

1. Strain gauge pressure sensor Strain gauge pressure sensors are sensors that measure pressure primarily by measuring the strain of an elastic element. Depending on the material, strain gauges are divided into metals and semiconductors. When the conductor and the semiconductor material are mechanically deformed, their resistance value will change.

1. The problem of the sealing ring of the pressure sensor The output of the pressurized transmitter does not change, and the output of the pressurized transmitter changes suddenly, and the zero position of the pressure relief transmitter cannot be returned, which is likely to be a problem with the sealing ring of the pressure sensor. It is common that due to the specification of the sealing ring, the sensor is tightened and tightened.

1. The reason for the total alarm of the sensor The total sensor alarm is when the sensor's alarm indicator is always on, but the sensor is not actually catching the outlier. This can happen for a variety of reasons, but here are some of the most common ones: 1. Sensor device ...