Whether it is a linear displacement sensor or a rope displacement sensor, it often encounters a variety of problems when it is used, including quality problems, application problems, environmental problems, etc., but the use of problems is common, and improper use is easy to damage the sensor.
1. The problem of small power supply capacity of linear displacement sensor
If the power supply capacity is insufficient, the following conditions will be formed: the movement of the melt will change the appearance of the clamping electronic ruler and shake, or the movement of the clamping will shake the appearance of the injection electronic ruler, resulting in a measurement error and becoming larger. This situation is more likely to occur when the driving power supply of the solenoid valve is shared with the power supply of the linear displacement sensor.
2. What are the requirements for the alignment, parallelism and viewpoint of the linear displacement sensor?
The linear displacement sensor of the device requires a high degree of sensor alignment, but the parallelism can tolerate an error of ±0.5mm, and the viewpoint can allow an error of ±12°. However, if the parallelism error and viewpoint error are both large, the number jumps will appear. When this happens, it is necessary to adjust the parallelism and viewpoint.
3. The problem of incorrect wiring of the linear displacement sensor
The three wires of the linear displacement sensor cannot be connected incorrectly, and the power line and output line cannot be replaced. If the above wires are connected incorrectly, there will be a large linearity error. If necessary, our company has a video of the wiring tutorial for our reference.
4. The problem of frequency modulation disturbance and electrostatic disturbance
Both FM and electrostatic disturbance may make the display of the electronic ruler jump digitally. Therefore, the signal line of the electronic ruler and the strong current line of the equipment should be separated from the trunking. It is necessary for the electronic ruler to be grounded mandatorically. The signal wire needs to be shielded, and a section of the electrical box should be grounded with the shielded wire. If there is a high-frequency disturbance, the voltage measurement of the multimeter will usually appear normal, but the displayed number will beat constantly; In the case of electrostatic disturbance, the situation is the same as that of high-frequency disturbance. To prove whether it is static disturbance, you only need to use a length of power cord to connect the cover screw of the electronic ruler with some metal on the machine, as long as it is shortened, the static disturbance will be eliminated immediately. However, if you want to eliminate high-frequency disturbance, it is difficult to use the above method, you can try to pause the source of high-frequency disturbance, and see if the results will be better, so as to determine whether it is a problem of high-frequency disturbance.
5. The data is beating regularly, or there is no problem with the data
In this case, it is necessary to check whether the insulation of the connecting wire is damaged, and the short circuit to the ground caused by regular contact with the shell of the machine.
|
More on that
|
Pressure Transmitter Verification Regulations
A pressure transmitter is a type of instrument that converts a pressure variable into a consistent output signal that can be transmitted, and there is a given continuous function relationship between the output signal and the pressure variable, which is generally a linear function. Pressure variables include positive and negative pressure, differential pressure and pressure. Pressure transmitters are available in electric and ...
|
|
Cable protection systems for harsh conditions
In addition to getting used to mechanical shock, pressure, and tensile strain, sensor cables are often exposed to chemical environments. While traditional sensor cable planning is often not sufficient to meet these requirements, the new cable maintenance system has been developed with this intention in mind, guaranteeing ...
|
|
Recognition of the number of pulse positions of the encoder
The pulse encoder is a rotary encoder that uses the rotation pulse for signal output, and the main characteristics are the standard shape and diversified shape structure; The internal coding is stable, the signal output qiang, and the pulse value and positioning value are clear. Therefore, when choosing this type of punching encoder, ...
|
|
The RHI90 series encoders have been fully upgraded
The new RHI90 series encoders offer significant improvements in electrical and mechanical performance
With the extensive use of electronic components and equipment in the field of automation, the risks of malfunction and damage caused by electrical and electromagnetic disturbances are also invisible.
|
|
The difference between fiber optic sensors and photoelectric sensors – we are blessed
Optical fiber sensor and photoelectric sensor are two typical sensors, which are widely used in production and measurement, so what is the difference between the two?
Fiber optic sensor skills are developed on the basis of fiber optics, optical communications, and optoelectronic skills, and electromagnetic...
|
|
Safety barriers are available in a variety of applications
In the process of using the safety barrier, whether it is the construction stage or the daily maintenance, repeated removal of the suture is a troublesome and simple mistake. With pluggable terminals, there is no need to repeatedly disconnect the wires. The field side terminals of the safety barrier and the system side terminals are distinguished by different colors, if there are two sets of ...
|
|
The principle of installation of safety barriers
1. The safety barrier should be installed in a safe place, and the environmental conditions should meet the requirements of the "application conditions" in the "Safety Barrier Selection Sample".
2. The connecting wires of the intrinsically safe end (blue end) and non-intrinsically safe end circuits of the barrier safety barrier are in the sink ...
|
|
Displacement sensor failure solution - double blessing
(1) Electronic ruler
When the electronic ruler is used to a certain moment, in the face of aging problems, we should pay attention to the fact that if the seal is now aged, and there are many impurities, water mixtures and oil, then it will affect the touch resistance of the brush, resulting in the continuous beating of the displayed numbers.
|
|
Features of image sensors – a blessing
Picture sensor is an extremely useful product, which has gradually attracted the favor of shopping malls with its strong sensitivity and speed.
The use of picture sensors in daily life is undoubtedly a digital camera product, and its development speed can be described as changing with each passing day. At...
|
|
What capacitive proximity sensors can detect – and what we can detect
Proximity switch is a kind of azimuth switch that can be operated without mechanical direct touch with moving parts, when the sensing surface of the object proximity switch to the action interval, the switch can be operated without mechanical touch and any pressure, so as to drive DC electrical appliances or computer (PLC) ...
|
|
Instructions for use of ultrasonic switches
The ultrasonic switch can be parameterized via two buttons on the side of the sensor. The width of the ultrasonic sound cone also allows the sensor to be mounted as required. The user can set the switch point according to his needs, and the switch point can be adjusted within 5 minutes after powering on. In more than 5 minutes, if ...
|
|
Engineered Vibration Sensor Test Methods – Blessing
In the field of engineering oscillation testing, there are various test methods and methods, but they can be divided into three categories according to the measurement methods of various parameters and the physical properties of the measurement process.
1. Mechanical quizzes
Will the works oscillate ...
|
|
The selection of proximity sensors follows the essentials – the blessing of the United States
For different raw material detection bodies and different detection intervals, different types of proximity sensors should be selected to make them have a high performance-to-price ratio in the system, for which the following principles should be followed in the selection:
1. When the detector body is a metal material: high-frequency oscillation proximity ...
|
|
Precautions for P+F safety barriers
First, it is necessary to pay attention to the capacitive and inductive resistance of cables and field equipment, explosion-proof is the explosion-proof system, in addition to the need for P+F safety barriers to reach the required explosion-proof level, the energy storage of cables and field equipment is also a key issue. Especially after parametric certification replaces system certification, engineering companies are especially ...
|
|
Eltra Incremental Rotary Encoder Types
Eltra incremental encoders fall into three categories:
Optical solid shaft incremental encoder Eltra. The couplings in these types are made of solid shafts.
· EL-ER 30 E/H；
· EH 38 A/B/D；
· EL-E ...
|
|
Commonly used sensor type – Doublebless
1. Semiconductor type Semiconductor gas sensor is a gas sensor that uses semiconductor gas sensing elements as sensitive elements, which is the most common gas sensor, widely used in combustible gas leakage detection equipment in homes and factories, and is suitable for the detection of methane, natural gas, liquefied gas, hydrogen, etc.
|
|
How to choose a sensor in the early stage?
In the early application and selection of sensors, how to choose is a very important point, and the selection is smooth, and the following will briefly say how the sensor is selected in the early stage.
The Viewpoint Sensor is in the real ...
|
|
The difference between a light sensor and a photoelectric sensor – we are blessed
Sensors we all know, at the same time the market demand is very large, there are many varieties, during which people are more commonly used light sensors and photoelectric sensors, although only a word difference, but the difference between the two is very large.
1. Different definitions:
...
|
|
The new WIS2 wireless sensing system is available
The use of robots that can exchange things requires high-speed movement and fast rotation. Conventional solutions for energy chains or slip rings lack the necessary flexibility with regard to this automation technology. Our wireless sensing system (WIS) enables non-contact in places where a fixed connection is not possible.
|
|
Introducing the Sofis Valve Position Indicator
Sofis, an expert in the operation of valves in the process industry, relies on sensors for its latest treatment solution, the "Valve Orientation Indicator" (VPI). VPI provides an overview of the orientation of manual valves in the plant network. Combined with integrated sensors and automatic detection...
|
|
Contact
working hours
