Rorobot BML-1G071010[P]/S The recommended load is 12g

Introduction: Rorobot Finger Module FMA8-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot BMC-3B14/S 　　Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot Finger Module A8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot B-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H] and non-marking type [ ...

Introduction: The multi-finger opposite hand claw has a large grasping strength, can be grasped in both directions by standing and lying down, has strong adaptability, and can perfectly solve the problems of shaking and positioning deviation when grabbing hanging parts. The soft material and adjustable grip force eliminate scratches and damages on the surface of the product. Aluminium profile frame, ...

Introduction: Soft Touch/Rorobot Independent Finger Module SMP-03 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module B5V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory package PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Robot Soft Jaw BML-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot BMC-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module B8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C3V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction:Rorobot Robot Soft Gripper BMC-20005V, B-20005V/S can be used well for 0.18mm-3mm between small and light and thin special-shaped workpieces, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot BMC-3A18[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G and the external support fingertip distance D. The soft claw material is divided into ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: It conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. The maximum load is recommended 20 kg Suitable for non-standard clamps ...

Introduction: FlexTouch/Rorobot Flange Connection Module FCM-R04 Features: It complies with the ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. Light weight, suitable for lightweight articulated robots, ...

Introduction: SoftTouch/Rorobot Connectivity Module CM Series Features: A full range of soft beak modules can be installed at the end Can be mounted on the soft beak series sliding mounting plate [SMP]. Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products layered grabbing ...

Introduction: Rorobot FM-A5V5/LS1 Features: Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g We take the guest ...

Introduction: Rorobot FM-A5V5/LS1 Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g Our customer-centric service ...

Introduction: Soft Touch/Rorobot Finger F-C4 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot Finger Module FM-B6V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...