Soft Touch/Rorobot Finger Module FM-B6V1 Finger height: 21mm

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction: Soft-Touch/Rorobot Skid Shift Mounting Plate SMP-4L Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module B8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: SoftTouch/Rorobot Connectivity Module CM Series Features: A full range of soft beak modules can be installed at the end Can be mounted on the soft beak series sliding mounting plate [SMP]. Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products layered grabbing ...

Introduction:Rorobot FM-C4V5/LS1[HAS] Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 16mm Safe working air pressure: 300kPa Suggested load: 380g Tare weight: 90g Our customer-centric ...

Introduction:Rorobot BML-3A18[HAS]/S,B-4BG64/S is an external gripper soft jaw, recommended clamping workpiece size (28-50)mm, opening and closing size in (50.4-80)mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S ...

Introduction: Soft Touch/Rorobot Finger Module B3V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot B-20606/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, and it is recommended to use it with a soft-touch air driver, and the fingertip distance G is supported to use the working air pressure adjustment. Soft-touch materials are divided into conventional type [H] and non-marking type, ...

Introduction: Soft Touch/Rorobot Finger F-C4 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot Finger Module FM-B5V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B6V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Rorobot Finger Module C3V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: Peculiarity...

Introduction: Rorobot Robot Soft Jaw BML-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot Soft Beak B-3B14 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product References ...

Introduction: Rorobot Soft Jaw BML-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot module B-3B12[H]/S is a small, slender soft claw, can support 6mm-12.3mm workpiece inside, in a small space, to achieve ring-shaped, cylindrical, hollow cylindrical and other small, limited external grasping space, fragile and fragile objects ...

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot BML-3G20[HAS]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional [ ...

Introduction: Rorobot Finger Module B5V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...