Rorobot FM-A5V5/LS1[PAS] weight 90g

Introduction: Rorobot soft beak module BM series can be installed in the connection module [CM] or flange connection module [FCM]; The soft beak module comprises a soft beak and a matching fitting joint; The module assembly is supplied with a straight-through fitting fitting (PN-066) or a side-through fitting fitting (PN-007); Soft beak ...

Introduction: Soft Touch/Rorobot Stand-Alone Finger Module SMP-02 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1[H], Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. I...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...

Introduction: Rorobot BML-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot Soft Jaw BMC-3B24[H]/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch material points ...

Introduction: Rorobot Finger Module C6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger F-B7 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B4V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Soft Jaw BMC-20802 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot Finger Module C7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: iPCU2 has two options: standard iPCU2-SMN and high-speed iPCU2-HMN, the high-speed type has a larger vacuum flow rate and is suitable for high-speed handling conditions. iPCU2 Passive Driver: Compact soft-touch passive actuator. -90~300kPa three-speed adjustable output air pressure range ...

Introduction: SoftTouch/Rorobot Gripper BOM Product parameters Skid Mounting Plate: SMP-02 Profile: P-20300 Connector: CP-04 Flange connection module: FCM-R06 Our customer-centric service concept: a full range of services to pursue ...

Introduction: Rorobot Finger Module A7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot BMC-3B12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...

Introduction: Rorobot BML-4G64[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module FM-A8V1, Features and Applicable Scenarios: Combination of Two-Finger Module, Compact Structure, Small Footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...