机器人FM-A5V5/LS1[P]

介绍：机器人机器人BML-1G071010[LP]/S 特征： 正压状态下指尖打开，真空状态下夹紧，建议采用软触风驱使用，指尖与工件的距离G可调节工作气压。 软爪材料分为...

简介：Rorobot手指模块FM-A8V2，特点及适用场景：独立安装，可安装SMP滑动安装板，手指间距和角度可调，固定方式：可从四个方向固定（可选），进气方式：可从三个方向安装进气连接器（可选） ...

简介：机器人手指模块B6V3，特点及适用场景：独立安装，可安装SMP滑动安装板，手指间距和角度可调。 特征： 特点及适用场景：独立安装，可安装SMP滑动安装板，手指间距和...

简介：Rorobot BMC-3G20[H]/S 特征： 正压状态下指尖打开，真空状态下夹紧，建议搭配触感柔软的空气驱动器使用，通过支撑指尖距离G即可调节工作气压。 触感柔软的材料分为常规型[H]型和无痕型[H]型。

简介：机器人手指模块FM-B5V1，特点及适用场景：双指模块组合，结构紧凑，占地面积小。间距和安装角度不可调节，适用于夹紧微小、薄、轻的工件。 特征： 特点及适用场景：两指...

简介：Rorobot BMC-3C12[H]/S 特征： 指尖在正压状态下张开，真空状态下夹紧，因此建议采用触感柔软的空气驱动使用，通过支撑指尖距离D即可调节工作气压。 触感柔软的材料分为常规型[H]型和无痕型[H]型。

Introduction: Soft Touch/Rorobot Finger Module FM-B7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot BML-4G64[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Rorobot Finger Module C3V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: Peculiarity...

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module B5V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BMC-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction:Rorobot FM-C4V5/LS1[HAS] Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 3mm Safe working air pressure: 300kPa Recommended load: 70g Self-weight: 20g Our customer-centric service ...

Introduction: Rorobot Finger Module FM-A7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...

Introduction:Rorobot Robot BMC-2G1211[HAS] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction:Rorobot soft claw BMC-4BG64/S, B-4BG64/S is an external gripper type soft claw, the recommended clamping workpiece size is (28-50) mm, the opening and closing size is (50.4-80) mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S is ...