Soft Touch/Rorobot Finger Module C3V3 Finger width 12mm

Introduction: Rorobot Finger Module FM-A6V2, Features and Applicable Scenarios: Independent Installation, Can be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BML-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot FM-C4V5/LS1 Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 9mm Safe working air pressure: 120kPa Recommended load: 145g Tare weight: 28g Our customer-centric service philosophy ...

Introduction: Soft Touch/Rorobot Finger Module C7V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify the Trachea Arrangement. It is mostly used in scenarios where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm Features: ...

Introduction: Rorobot B-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular type [H] and non-marking type ...

Introduction: Rorobot Finger Module C8V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in scenarios where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm Features: ...

Introduction: Rorobot Finger Module FM-A8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1[H], Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. I...

Introduction: Rorobot Finger Module A8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger F-B6 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft jaw material is divided into conventional type, when the weight of the workpiece ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot Finger Module FMA8-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...

Introduction: Rorobot Robot Soft Jaw BMC-3G20[HAS]/S, B-3G20[H]/S is a strong small soft jaw that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the other three-finger soft claws in gripping higher ...

Introduction: Rorobot Soft Beak B-2B 　　Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product parameters ...

Introduction: Rorobot Finger Module B6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Soft Touch/Rorobot Finger Module FM-B7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot BMC-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...