Rorobot BMC-20005V[P] External gripping blessing force 0-0.3N

Introduction: Rorobot Finger Module FM-A7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, suitable for clamping tiny, thin and light workpieces, and the fixing method: can be fixed from three directions. Features ...

Introduction: Rorobot BMC-3B12[H]/S Product parameters Tare weight: 3.3g Maximum load: 10g External gripping force: 0.1N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 24 ...

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C8V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module FM-A7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Soft Touch/Rorobot Independent Finger Module SMP-01 Features: According to the length of the slot, it is divided into SMP-01 / SMP-02 / SMP-03 It can be used for the assembly between the finger module [FM] and the aluminum profile The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Soft Jaw BML-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction:Rorobot BML-4BG64/S, B-4BG64/S is an external gripper type soft jaw, the recommended clamping workpiece size is (28-50) mm, the opening and closing size is (50.4-80) mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S is ...

Introduction: Soft Touch/Rorobot Finger Module FE-A3V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces. Features: Features and applicable scenarios: ...

　　Introduction: Rorobot B-3B10[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and ...

Introduction: Rorobot Finger Module C5V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory package PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Finger Module C3V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Rorobot B-20802 Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft touch materials are divided into conventional type and non-marking type.

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot BMC-20603[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Soft Jaw BMC-2G1624[HB]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft claws ...

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction:Rorobot Robot BMC-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...