Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. The angle of incidence, surface characteristics, object color, etc., do not affect the reliability of the sensor.
Product Details
Compact design with versatile mounting options
IO-link interface for service and process data
Multiple frequencies to prevent mutual interference (anti-crosstalk)
Extended temperature range
-40°C ... 60°C
High degree of protection: IP69K
Transmitter OBE12M-R100-S-IO
Receiver OBE12M-R100-2EP-IO
General specifications
Effective detection distance 0 ... 12 m
The limit value of the detection range is 15 m
Light source LED
Light source type Modulates visible red light
LED Hazard Rating Marking Exempt Group
The dot diameter is approximately 65 mm and 1 m apart
Divergence angle 3,7 °
Ambient light limit EN 60947-5-2 : 30000 Lux
Functional safety-related parameters
MTTFd 462 a
Mission time (TM) 20 a
Diagnostic Coverage (DC) 0 %
Indicator/method of operation
Working Indicator Green LED:
Lights up continuously - powered
Flashing (4Hz) - Short circuit
Flashing with short intermittent (1 Hz) - IO-Link mode
Function Indicator Yellow LED:
Solid - The light path is unobstructed
Continuous Off - Object detected
Flickering (4 Hz) – Insufficient operating reserve
Control Element Receiver: Bright/Dark On
Control Element Receiver: Sensitivity Adjustment
Parameterized indicator IO Link communication: Green LED temporarily off (1 Hz)
Electrical Specifications
Operating voltage 10 ... 30 V DC
Ripple max. 10 %
No-load current Transmitter: ≤ 14 mA
Receiver: ≤ 13 mA at 24 volts
Protection class III
interface
Interface Type IO-Link (via C/Q = Pin 4)
IO-Link fix 1.1
Device ID Emitter: 0x110401 (1115137)
Receiver: 0x110301 (1114881)
Transmission rate COM 2 (38.4 kb/s)
Minimum cycle time 2,3 ms
Process Data Bit Width Emitter:
Process data output: 2 bits
Receiver:
Process data entry: 2 digits
Process data output: 2 bits
SIO mode support Yes
Compatible with primary port type A
input
Test Input: Under +UB the transmitter is deactivated
output
Switch Type The switch type of this sensor is changeable. The default settings are:
C/Q - BK: NPN NN/D, PNP N/IL, IO-Link
/Q - White: NPN Normally Closed/Bright, PNP Normally Open/Dark
Signal output: 2 push-pull (4-in-1) outputs, short-circuit protection, reverse polarity protection, overvoltage protection
Switching voltage max. 30 V DC
Switching current max. 100 mA, impedance load
Use categories DC-12 and DC-13
Voltage drop ≤ 1,5 V DC
Switching frequency 1000 Hz
Response time 0,5 ms
compliance
Communication interface IEC 61131-9
The product standard is EN 60947-5-2
Certifications and certificates
UL listed E87056, cULus recognized, class 2 power supply, type class 1
Environmental conditions
Ambient temperature -40 ... 60 °C (-40 ... 140 °F) to secure the cable
-25 ... 60 °C (-13 ... 140 °F), movable cables are not suitable for conveyor chains
Storage temperature -40 ... 70 °C (-40 ... 158 °F)
Mechanical Specifications:
Housing width 11 mm
Housing height 37,1 mm
Case depth 21,5 mm
Degree of protection IP67 / IP69 / IP69K
Connect a 2 m fixed cable
material
Housing PC (Polycarbonate)
Optical end-face PUMA
Mass Transmitter: approx. 10 g Receiver: approx. 10 g
Cable length 2 m
The company has been customer-centric, the concept of creating value for customers, winning the market with quality and service, and sincerely hopes to cooperate with all sectors of society to create success, create brilliance together, and work together to create a better tomorrow! In line with the concept of credibility and service-oriented, the company warmly welcomes new and old customers to inquire, visit and negotiate business!
|
More on that
|
The P+F/GIF sensor GLD3-RT /115/147 is programmable
Product Description: Visolux/ Pepperl+Fuchs has developed a range of special sensors for industrial use that extend the range of applications for common sensors. These special photoelectric sensors allow the customer to find a more suitable solution.
Specifications:
...
|
|
P+F sensor NBN40-L2-E0-V1 40 mm non-flush
Introduction: NBN40-L2-E0-V1 is a kind of switch sensor (i.e., non-contact switch), which has the characteristics of travel switch and micro switch, and has sensing performance, and reliable action, stable performance, fast frequency response, long application life, strong anti-interference ability, etc.
|
|
P+F/Triangulation sensor OBT300-R100-2EP-IO-V31-L
Product Description: Triangulation sensor with background suppression, miniature design with multiple mounting options, best-in-class background suppressor, precise object detection, virtually color-independent, extended temperature range
Our customer-centric service philosophy ...
|
|
P+F/Background Suppression Sensor MLV41-8-HV-60-IR-5360
Product Description: Visolux/ Pepperl+Fuchs has developed a range of special sensors for industrial use that extend the range of applications for common sensors. These special photoelectric sensors allow the customer to find a more suitable solution.
Specifications:
...
|
|
P+F/Slot sensor GL-ES-IR /115/120 60V DC
Product introduction: There is a special through-beam sensor in our products called fork sensor. It is mainly used in places where the measurement distance is short. Since only one device requires wiring, fork sensors have the advantage of being easy to install compared to standard control sensors. ...
|
|
P+F/Fork sensor GL30-IR / 32 / 40A / 98A
Product introduction: There is a special through-beam sensor in our products called fork sensor. It is mainly used in places where the measurement distance is short. Since only one device requires wiring, fork sensors have the advantage of being easy to install compared to standard control sensors. ...
|
|
P+F/Optical Data Coupler DAD15-8P Spring Terminals
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F Inductive Sensor NBB15-30GM50-WS Quasi-flush
Summary: Inductive proximity sensors are the preferred product for most applications that require the precise and non-contact detection of metal objects in mechanical or automated equipment. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality electrical products.
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40-SE2-V1 PNP
Product introduction: The working principle of ultrasonic through-beam sensor is to detect an object by emitting sound waves from the transmitter to the receiver and being interrupted by the sound beam by the target object. The transmitter generates an ultrasonic signal that is received and evaluated by the receiver. When the ultrasonic beam is attenuated or interrupted by an object, the receiver ...
|
|
P+F/Logic control devices up to 100 kHz
Introduction: Logic control units are widely used in the automation industry. In practice, they are capable of detecting digital or analog signals, displaying them and monitoring them. In order to solve the conversion and application between signals, we provide digital display meters, counters ...
|
|
P+F/Through-beam photoelectric sensor BB10-P/59/76b/103/115e
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/UB120-12GM-E5-V1 connector M12
Product Introduction: The transducers used to transmit and receive sound waves are separated, so that the system does not need to wait for the signal attenuation of the transmitter, thus effectively reducing the dead zone. The direct detection type of ultrasonic sensors is available with switching and analog outputs. Direct detection of all support window mode functions ...
|
|
P+F/Optical fiber optic sensor SU19.1/110/115 30μs
Product Introduction: Classic Series Fiber Optic Sensor with Display, Slave Module, Push-Pull Output, Fixed Cable, Classic Line with Display, AGC (Automatic Gain Control) for Faster Teach-in, Combined Installation, Easy Wiring, Transparency Recognition, 30μs High Speed Mode.
...
|
|
P+F/Inductive sensor NBN4-12GK50-E0/E2 voltage drop ≤3V
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F Capacitive sensor CCB10-30GS55-N1-V1
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Encoder RVI50N-09B**A*T 80mA
Introduction: An incremental encoder provides a fixed number of pulses in one revolution, and the speed is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. The accuracy of incremental encoders depends on mechanical and electrical factors ...
|
|
P+F/Inductive sensor NBN30-U1-A0/A2 non-flush 30mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/Inductive sensor NBB3-V3-Z4 3 mm flush
Summary: Inductive proximity sensors are the preferred product for most applications that require the precise and non-contact detection of metal objects in mechanical or automated equipment. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality electrical products.
|
|
P+F Incremental Rotary Encoder 10 - 2133 X
Introduction: The speed of an incremental encoder is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. A dual-channel output encoder that is a two-channel encoder with two ...
|
|
P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 20 g
Description: The P+F/P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 with its ultra-small housing design and 45° cable outlet provides maximum installation freedom, even in very space-constrained conditions.
Product Features ...
|
|
Contact
working hours
