Description: The P+F/P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 with its ultra-small housing design and 45° cable outlet provides maximum installation freedom, even in very space-constrained conditions.
Features:
Ultra-small housing design
The 45° cable outlet offers maximum installation freedom, even in very space-constrained conditions
Increase the availability of the machine with a wear-resistant, antistatic front glass panel
It has a very large detection range in long-range mode
Optionally switch to high-precision mode for higher switching accuracy
Product parameters
Effective detection distance
Long range mode: 0 ... 2 m
High Accuracy Mode: 0 ... 200 mm
Detection range limit values
Long range mode: 2,5 m
High precision mode: 300 mm
Light source: LED
Light source type: Modulated visible red light, 630 nm
Angular deviation : approx. 2°
Spot diameter
Long range mode: 150 mm 2000 mm apart
High precision mode: 0,5 mm at a distance of 50 mm
Divergence angle : approx. 2 °
Optical end face: direct forward beam
Ambient light limit: EN 60947-5-2 : 30000 Lux
MTTFd ：806 a
Mission Time (TM): 20 a
Diagnostic Coverage (DC): 0 %
Working indicator: Green LED, solid on, energized, Short circuit: Green LED flashing (approx. 4 Hz)
Function Indicator: Receiver: Yellow LED, lights up when the beam is unobstructed, flashes when the stability control is insufficient; Turn off when the beam is interrupted
Operating voltage :10 ... 30 V DC, Class 2
No-load current
Emitter: ≤ 11 mA
Receiver: ≤ 8 mA
Control Inputs: Transmitter Selection BK: Not Connected, Long Range Mode BK: 0 V, High Precision Mode
Switching Threshold: Teach-in input
Switch Type: Normally open contact
Signal output: 1 NPN output, short circuit protection, reverse polarity protection, open collector
Switching voltage: max. 30 V DC
Switching current: 50 mA max
Voltage drop : ≤ 1,5 V DC
Switching frequency: approx. 800 Hz
Response time: 600 μs
Ambient temperature :-25 ... 60 °C （-13 … 140 °F）
Storage temperature :-30 ... 70 °C （-22 … 158 °F）
Housing width : 7,5 mm
Housing height: 24 mm
Case depth : 11,2 mm
Degree of protection: IP67
Connection: 2 m fixed cable
material
Housing :P C/ABS and TPU
Optical endface: Glass
Cable :P UR
Installation : fixing screws , 2 x M2 socket screws included in delivery
Mass: approx. 20 g per sensor
Cable length: 2 m
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action, and every day of service are professional and careful, can we meet or even exceed customer expectations, so that customers can be satisfied and recognized by us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces the P+F/Double Beam Photoelectric Sensor OBE2000-R2-SE0 20g product, if you are interested in P+F/Double Beam Photoelectric Sensor, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F Isolation Barrier K Series 35mm DIN Rail
Introduction: The widely used K series intrinsically safe isolation grid adopts DIN rail installation, which is flexible and convenient. The intrinsically safe barriers of the K series can be easily plugged into the power rails assembled with the DIN rails. This installation method can greatly save ...
|
|
P+F/Inductive sensor NBN4-12GM40-E0/E2 DC 4mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/Pixel Fork Sensor GL5-J / 28A / 115 J design
Product introduction: Miniature photoelectric slot sensor is used to detect small parts, J-shaped design, fork width 5mm, infrared light, NPN output, fixed cable, miniature design, optimized for detecting small parts, high switching frequency, simple and quick installation, clearly visible LED function display.
...
|
|
P+F/UBE15M-F54-H1-V1 housing PBT
Introduction: An ultrasonic through-beam sensor consists of a transmitter and a receiver mounted facing each other. Ultrasonic through-beam sensors work by emitting sound waves from the transmitter to the receiver to detect objects through the sound beam being interrupted by the target object. The emitter produces ultrasonic ...
|
|
P+F/Through-beam photoelectric sensor BB10-P/59/76b/103/115e
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F/Bi-material sensor UDC-18GM50-255S-3E0
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F/MLV11-8-500-Ex/40b/112 60g
Description: The P+F/Photoelectric Sensor MLV11-8-500-Ex/40b/112 is ATEX certified for Zone 1 (gas); Intrinsically safe, explosion-proof operating specification IA IIC T6 Gb; Diffuse photoelectric sensors for standard applications; Sensitivity adjustable.
...
|
|
P+F/Inductive sensor NBN4-12GM50-E2-V1-Y89925
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F Incremental Rotary Encoder 10 - 2133 X
Introduction: The speed of an incremental encoder is calculated by the number of pulses measured per unit of time. To measure angles and positions, it is common to start counting from a starting reference point. A dual-channel output encoder that is a two-channel encoder with two ...
|
|
P+F/Bejiafu capacitive sensor CJ15+U1+A2 wire cross-sectional area of 2.5mm2
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CJ4-12GK-N-5M with a rated voltage of 8V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Sensor NBN4-12GM40-E2-V1 4 mm
Introduction: The inductive sensor is to use electromagnetic induction to convert the measured physical quantities such as displacement, pressure, flow, vibration, etc. into the change of self-inductance coefficient and mutual inductance coefficient of the coil, and then convert the output of voltage or current change by the circuit to realize the conversion of non-electricity to electricity.
...
|
|
P+F/Pixel Sensor GL30-RT / 32 / 40A / 98A Light/Dark
Product Introduction: Photocell Sensor, Zinc Die-Cast Housing, 30mm Slot Width, Red Light, Light/Dark, Sensitivity Regulator, DC Version, PNP Output, 3-Pin M8 Plug, Optimized for Detecting Small Parts, High Switching Frequency, Multi-Device Installation Possible, No Mutual Interference (No Crosstalk), Sensitivity ...
|
|
P+F/Multi-line LED Scanner R2100 4-20mA analog output
Product Introduction: The R2100 Multi-Ray LED Scanner, also known as a 2D LiDAR sensor, combines pulsed ranging technology with ultra-infrared LEDs and multi-beam scanning to further advance the realm of possibilities. Multiple LED emitter elements arranged next to each other provide a two-dimensional surface with eleven points of light ...
|
|
P+F/Through-beam GD18 / GV18 /115/120
Product Introduction: Thru-beam sensor, M18 threaded housing design, plastic housing, front optical surface, 20 meters detection distance, red light, light and dark, DC version, 2 PNP outputs, fixed cable, high efficiency line, short M18 plastic housing application, very high detection range, 4 LED fingers...
|
|
P+F capacitive sensor CJ10-30GK-WS housing diameter 30 mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Inductive sensor NBN4-12GM50-E1 with a housing diameter of 12 mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F inductive sensor NBB0,6-3M22-E2 pulse
Description: P+F Inductive sensor NBB0,6-3M22-E2 pulse, nominal working distance: 0,6 mm, operating voltage: 10 ... 30 V, switching frequency: 0 ... 1400 Hz
peculiarity
0.6 mm, flush
Miniature design
Product parameters
...
|
|
P+F magnetic field sensor MMB60-12H50-E2-V1 60 mm
Introduction: Magnetic sensors with M12 cylindrical housing are used in conventional magnet detection. A non-contact detection sensor for piston position is also available for steel hydraulic cylinders. These sensors are easy to install and do not require a mounting slot or installation in the cylinder.
|
|
P+F photoelectric sensor M100/MV100-RT/35/76a/95/103
Description: The through-beam sensors are designed in a miniature design with a slit in the light of the miniature sensor, which is easy to use, very bright, with a high visible light point, full metal threaded mounting, and the high-efficiency series is mounted in a short M18 plastic housing for standard applications.
...
|
|
Contact
working hours
