Tianyi switch - the environmental conditions of the high-voltage load switch

Pre-stroke - indicates the distance or angle at which the actuator on the limit switch must move before tripping the switch contact Operating Point - Indicates the position of the actuator when the switch contact is moved to the working position Release Point - Indicates the position of the actuator when the contact returns to its original state Differential - ...

1. Common air switch models in the family Common family models: DZ series, C16, C32. C40, C80, C100, C120 and other products, of which C represents the starting current, such as: C32 means that the starting current is 32A, which can drive a 6500 watt water heater, C40 ...

(1) Eddy current proximity switch This type of switch is sometimes called an inductive proximity switch. It is the use of conductive objects when they are close to the proximity switch to produce eddy currents inside the object. This eddy current reacts to the proximity switch, causing the internal circuit parameters of the switch to change, so as to identify the presence or absence of ...

JD series warning light is Tianyi electrical appliances in the field of signal control launched high-performance products, once launched, it has won the unanimous favor of customers, products in the design, manufacturing, quality control and other aspects of the company's quality system has always been under the strict testing and supervision of the company's quality system, to ensure that each product ...

1. Through the isolation switch, it plays a good insulating role, so that the whole circuit can be safe and secure, and the maintenance personnel or staff also have enough ability to repair the circuit. 2. At the same time, the low-voltage isolation switch can also change the operation mode of the circuit, which is used in the power plant or gas plant.

1. Check the key points: 1) Whether the voltage at point B is 310V. 2) Whether the 15V voltage is normal. 3) Whether the voltage at point C is greater than 14V. 4) Whether the SS terminal of (8) pin IC6 is higher than 10V, whether the SD terminal of pin (10) is lower than 0.6V, and whether there is a square wave transmission at pin 13 and pin 14 ...

It is mainly divided into ATS and STS. STS static toggle switch STS (Static Transfer Switch), also known as static transfer switch. The STS automatically switches to the second channel to supply power to the load after the first channel fails.

1) When there is a power outage for any reason and the power cannot be restored in a short period of time, the backup power supply must be activated 1. Cut off the circuit breakers of the mains power supply (including the circuit breakers of the control cabinet in the distribution room, and the mains power supply cut-off of the dual power switching box), and pull the double-cast anti-reverse switch to the side of the self-provided power supply to ensure that the power supply is protected.

(1) The cost of linear power supply is higher than that of switching power supply at a certain output power point. Therefore, with the development and innovation of power electronics technology, the switching power supply technology continues to break through and innovate.

1. Install the dual power transfer switch with the power supply to ensure the correct access of the power supply. 2. Adjust the handle of the dual power transfer switch to the "automatic" position, so that the power supply will automatically detect the state of the other power supply, when one of the power supplies fails, the other power supply will ...

1. The high-voltage load switch can be broken with load and has the function of self-extinguishing arc, but its breaking capacity is very small and limited. 2. The high-voltage isolation switch is generally not able to break with load, there is no arc extinguishing cover in the structure, and there is also an isolation switch that can break the load.

1. When closing, first of all, attention should be paid to check that the circuit breaker that can be connected to the dual-power automatic transfer switch is indeed in the opening position, and then quickly operate the risk isolation switch to close it (whether the enterprise adopts manual management agency or leveraged financial institution personnel operation), but ...

1. Increase inductance and output capacitance filtering According to the formula of the switching power supply, the current fluctuation in the inductor is inversely proportional to the inductance value, and the output ripple is inversely proportional to the output capacitance value. Therefore, increasing the inductance and output capacitance can reduce ripple. In the same way, the output ripple is the same as the output ...

1) Ambient air temperature: The upper limit of ambient air temperature is +40°C, the lower limit of ambient air temperature is -5°C, and the average value of ambient air temperature for 24h does not exceed +35°C 2) Altitude: The altitude of the installation site does not exceed 2000m. 3) Atmospheric conditions: Atmospheric relative humidity in the surrounding air ...

1. Provide an electrical interval and a visible disconnection point during electrical equipment maintenance to ensure the personal safety of maintenance personnel [3] . 2. The disconnector can not be operated with load: it cannot be operated with rated load or large load, and it cannot be divided and combined with load current and ...

1. If it is installed on metal, a certain space must be ensured to avoid interference between the proximity switch and the metal other than the detection object, resulting in failure. The metal parallel to the sensing surface must be 3 times the sensing distance from the sensing surface. The metal around the shaft of the proximity switch must be outside the cylinder, close to ...

1) Clean the dust on the surface of the porcelain, check whether the surface of the porcelain is glazed or damaged, whether there are cracks and flashover marks, and whether the iron and porcelain joints of the insulator are firm. If the damage is severe, it should be replaced; 2) Wipe the oil stains on the blades, contacts or fingers with gasoline and check the contact ...

T-cam switches and P-block switches are used in a wide range of standard circuits and currents, and the number of combinations of cam switches is virtually unlimited. Different designs, front panels and dedicated switches ensure optimum sensitivity to meet the requirements. Q1: P switch and T switch have ...

First, first place the dual power supply on the adjustment table, and the phase wire and the neutral wire (neutral line) are docked in place, and can not be connected wrongly. Second, after the line is connected, it is necessary to check the installed line, and then turn on the main switch of the debugging station to turn on the common and standby working power supply. Three, when the double ...

1. Use less plastic switches The switch is composed of a panel, a current carrier, a nozzle and a base, etc., and a good switch is mostly made of stainless steel inlay, which is safe and anti-electric shock. On the contrary, most of the inferior switches are made of plastic, although they are insulated, they are prone to leakage and flammability, and potential safety hazards will occur. 2 ...