Tianyi switch - dual power supply automatic transfer switch operating procedures

In the design of switching power supply, the physical design of the PCB board must be proper, otherwise it may cause excessive electromagnetic interference and lead to unstable power supply. 1. The design process from the schematic diagram to the PCB should be rigorous and perfect: the establishment of component parameters ...

1. Change the reference current of the feedback module Regulating the reference current is the most basic way to regulate the output current of a switching power supply, and it can usually be achieved by rotating a potentiometer or toggling a switch. Changing the reference current allows the magnitude of the feedback current to be compared with it, so as to control the switch ...

1 The contact is overheated Contact heat is mainly caused by the current flowing through the contact, and there is power loss between the contacts (such as contact resistance loss, arc energy loss). It is normal for the contacts to heat up, but severe heat (overheating) is a malfunction. The main ...

1. Pull together the voltage transformer and lightning arrester under normal conditions. 2. Pull together the 220kV no-load bus. 3. The neutral point of the transformer when there is no ground fault in the latching grid. 4. Pull the bypass current that is closed by a switch or an isolated switch. 5. Outdoor vertical splitting triple isolation ...

1. Check the key points: 1) Whether the voltage at point B is 310V. 2) Whether the 15V voltage is normal. 3) Whether the voltage at point C is greater than 14V. 4) Whether the SS terminal of (8) pin IC6 is higher than 10V, whether the SD terminal of pin (10) is lower than 0.6V, and whether there is a square wave transmission at pin 13 and pin 14 ...

performance 1. Adopt double-row composite contacts, cross-connected mechanisms, micro-motor pre-energy storage and micro-electronic control technology, basically achieve zero arcing (no arc extinguishing cover); 2. Adopt reliable mechanical interlocking and electrical interlocking technology; 3. Adopt zero-crossing technology; 4、 ...

1. It can isolate the power supply, have obvious disconnection points, and is mostly used for fixed high-voltage equipment. 2. It has an arc extinguishing device and a certain opening and closing speed, and can pass the normal working current and the specified short-circuit circuit in the closing state. 3. It is strictly forbidden to turn on and off the circuit with load.

1. It can isolate the power supply, with a significant disconnection point, and is mostly used for fixed high-voltage devices; 2. It has arc extinguishing equipment and a certain opening and closing rate, and can pass through the normal working current and the specified short-circuit circuit in the case of closing; 3. It is forbidden to connect and cut off the circuit with load, ...

1. The air switch is an important electrical appliance in the low-voltage distribution network and power drive system, which integrates control and a variety of protection functions. In addition to completing contact and breaking circuits, it can also generate short circuits to circuits or electrical equipment. Protection against severe overloads and undervoltages, etc.

1. What are the common faults? Answer: The common faults of the disconnector are: (1) The contact part is overheated. (2) Porcelain insulation damage and flashover discharge. (3) Refuse to pull and close. (4) Wrong pulling and closing. 2. The overheating of the contact part of the disconnector during operation is caused by ...

1. The high-voltage load switch can be used as a load switch, which has the effect of self-extinguishing arc, but its breaking volume is very small and very limited. 2. The high-voltage isolation switch generally cannot be used as a load switch. There is no arc extinguishing cover in the structure, and there are also disconnectors that can switch loads on and off, but the structure is different from load switches ...

1. Buttons 1. Red Operation in hazardous situations. It is often used for emergency stops Stop and break. It is often used to stop all machines, stop one or more motors, stop a certain part of a piece of equipment, make the electrical components lose power, and have a stop function reset button. ...

1. Determine the type and protection form of the circuit breaker according to the requirements of the line for protection - determine the selection of frame type, device type or current limiting type. 2. The rated voltage UN of the circuit breaker should be equal to or greater than the rated voltage of the protected line. 3. The rated voltage of the circuit breaker undervoltage tripper ...

daily life There are many aspects of the use of limit switches, and it is found in many electrical appliances. So what effect can such a simple switch have? It is first and foremost a chain maintenance effect. The most common example is its use in washing machines and tape recorders (video recorders). ...

1. Increase inductance and output capacitance filtering According to the formula of the switching power supply, the current fluctuation in the inductor is inversely proportional to the inductance value, and the output ripple is inversely proportional to the output capacitance value. Therefore, increasing the inductance and output capacitance can reduce ripple. In the same way, the output ripple is the same as the output ...

2P means two poles, which means that this air switch has two connection ports, one to connect to the neutral wire and one to the live wire, which is suitable for single-phase circuit connection, or can also be used to connect two-phase power supply in a three-phase circuit. 3P is the meaning of three poles, there are three connection ports, and all of them are ...

JD series warning light is Tianyi electrical appliances in the field of signal control launched high-performance products, once launched, it has won the unanimous favor of customers, products in the design, manufacturing, quality control and other aspects of the company's quality system has always been under the strict testing and supervision of the company's quality system, to ensure that each product ...

During the "Twelfth Five-Year Plan" period, China deepened reform and opening up and accelerated the transformation of economic development mode. Transformation and upgrading is the only way for the sustainable development of the machine tool industry, and the top priority of the industry's transformation and upgrading is to enhance the market competitiveness of high-end CNC machine tools. Exhibitors will take advantage of the CCMT ...

What are the uses of air switches 1. The air switch is an important electrical appliance in the low-voltage distribution network and power drive system, which integrates control and a variety of protection functions. In addition to completing contact and breaking circuits, it can also generate short circuits to circuits or electrical equipment. Severe...

1. After opening, establish a reliable insulation gap to separate the equipment or line that needs to be overhauled from the power supply with an obvious disconnection point to ensure the safety of maintenance personnel and equipment. 2. According to the operation needs, change the line. 3. It can be used to divide and combine small currents in the line, ...