Inverter daily inspection items - Xinjie

Xinjie PLC conditions are established, why is the corresponding coil not in place? There are two possible reasons for this: (1) The same coil may be used in multiple places to perform the double coil output, and when the double coil is output, the coil on the rear side will operate first. （2） ...

Although many relays, timers and counters are often used in the ladder diagram programs used by PLCs, PLC does not have these hardware physically, but uses memory and program programming methods to do logic control and editing, and connects external mechanical devices to make physical devices through output components.

The development status of human-computer interface shopping malls in China China is the shopping mall with the largest demand for human-computer interface in the world, but it is not the shopping mall with the highest sales of human-computer interface products in the world.

1. For the switching input and output circuits, pay attention to the consistency criterion of maintaining the situation; The positive logic criterion is usually used, that is, when the input and output are live, it is the "ON" state and the data value is "1"; On the other hand, when the input and output are powered off, it is in the "OFF" state and the data value is "0". Such...

Confirm the rated power and resistance value of the braking resistor. The rated power of the braking resistor should be determined according to the power and moment of inertia of the motor, and the resistance value should be selected according to the specifications of the VFD. In the VFD's parameter settings, find the parameters related to the braking resistor, such as the braking resistor selection ...

When we select the right inverter brand, we need to recognize whether it can help enterprises better manage the risks and costs caused by potential safety, security and downtime accidents. Safety: Reverse arc drives assist users in meeting stringent reverse arc specifications. These inverters (Variabl ...

The motor soft starter is a new type of starting equipment designed and produced by using power electronics skills, microprocessing skills and modern control theory. The motor soft starter can effectively limit the starting current of the AC asynchronous motor when starting, and can be widely used in wind ...

(1) There is no need to adjust the parameters, we can maintain the original parameters (default value) when the inverter leaves the factory. (2) It is the parameter that needs to be set and changed before the trial operation. (3) It is a parameter that is adjusted in the operation of the demand. Frequency converters ...

Following the launch of XDH, XLH series 16-axis and other models, Xinjie has achieved good market feedback, and the XLH-30A32 low-profile controller to be launched today can be expanded by 32 bus nodes, and has better performance in basic performance and bus control ability. ...

As one of the important equipment for manufacturing motors, the six-station high-speed inner winding machine is widely used in electric fans, range hoods, purifiers, automobiles and other occupations. Now there are single station, double station, four station and six station winding machine types, and the six-station inner winding machine launched by Xinjie can reach up to 1200 times/i ...

1. On the premise of satisfying the production equipment and process requirements, the acceleration or deceleration time should be increased as much as possible, and then the overcurrent generation in the process of acceleration or deceleration can be avoided. 2. Check whether the inverter, motor, and production equipment are well matched, whether the transmission part is sensitive, and whether the material is ...

Why does the motor driven by the inverter overheat? This is due to the fact that the voltage of the inverter drive motor contains a rich high-frequency component. The voltage waveform of the inverter-driven motor is not a sine wave voltage, but a pulse-width modulation (PWM) voltage. According to Fu Liye's analysis, this waveform ...

The XDHI XLH series of 16-axis high-performance EtherCAT controllers is the perfect choice for small motion control. Product model XDH-30A16-E/XDH-30A16L-E Small/16-axis type Frequency: 600MHz Program Capacity: ...

From 14:00 to 15:20 on May 14 last year, the X-SIGHT visual brand conference with the theme of "Vision, Light Up Intelligent Manufacturing" was held online, officially announcing that Wuxi Xinjie and Intel will join hands to create a new era of intelligent manufacturing. X-SIGHT unveiled a new Intel chip-based ...

In the process of century industry, the more top-level software and hardware planning for the suspension of frequency conversion skills, first according to the characteristics of traditional air compressor motors, comprehensively analyze the causes of energy consumption and operation characteristics, so as to plan the control of frequency conversion skills speed regulation, air skill tightening, pressure sensing skills improvement, etc.

Introduction to Thermal Transfer Transfer printing refers to a printing method that selects the corresponding pressure to transfer the graphics and text on the intermediate carrier film to the substrate, and according to the different selection pressures, transfer printing can be divided into water transfer printing, heat transfer printing, air transfer printing, screen transfer printing, low temperature transfer printing and so on. In the meantime, the heat ...

At present, in the domestic PLC market, there are many kinds, but there are not many domestic PLC manufacturers with real strength, most of the domestic PLC is not an individual without legal person qualifications, or a single-chip microcomputer enthusiast, from the domestic PLC factory to buy the underlying programming code or buy a domestic PLC chip (the domestic P ...

Tile programming features The editing and display mode in all Chinese greatly improves the readability of the program; Customizable programming instructions. Not only can the name of the instruction be modified according to the characteristics of the industry, but also the instruction can be added or deleted according to the needs of the equipment; Adopt a procedural editing mode. ...

Motor overload: There is no need to set overload maintenance parameters in frequency conversion. The inverter generally acquiesces to the motor overload maintenance based on the motor power. Generally, it is 1.2 times 60 seconds to report the overload problem. The overload factor is not the same for different frequency converters. ...

Communication: (1) Radiation disturbance; (2) Conduction disturbance Anti-disturbing method: Regarding the disturbance signal transmitted by the radiation method, it is mainly weakened by wiring and shielding the radioactive source and the disturbed line. With regard to the disturbance signal transmitted through the line, ...