Banner Sensors – A debugging method for fiber optic sensors

1. Resistive type A resistive sensor is a device that converts measured physical quantities such as displacement, deformation, force, acceleration, humidity, temperature, etc. into resistance values. There are mainly resistive strain, piezoresistive, thermal resistance, thermal, gas-sensitive, moisture-sensitive and other resistive sensing.

How to use the emergency stop button 1. When there is an emergency on the scene, press and lock the red mushroom head button switch or round button switch; 2. Use the safety lock to lock the emergency stop button cover. The role of the emergency stop button 1. Make the machine in any case, immediately ...

1. There are 4 wires for the wiring sensor, among them, the red or brown wire is connected to the positive power supply, and the black wire is connected to the negative power supply; The green or blue wire is the dark output line, and the white or yellow wire is the bright output line, the user can choose one of them according to his needs, and the other is not used, but it should be insulated. Lines are not allowed ...

1. The size of the photoelectric sensor should be in line with its own production environment, and it needs to be measured before selection. 2. Select the sensing mode suitable for the environment and choose it appropriately. 3. The selection of sensing range should be carried out according to the production environment of its own products, regardless of the range ...

1. Optical adjustment The factory setting of the sensor is a large range, and this setting is subject to change. Note: Only use your finger to press the button. 2. Set the range (when stationary) 1. Adjust the sensor with a reflector; 2. Press the button for about 3s until two ...

1. Detection of temperature The optical fiber temperature sensor uses a polymer temperature-sensitive material that matches the refractive index of the optical fiber to coat the outside of two optical fibers that are fused together, so that the light energy is input from one optical fiber to the reflective surface and output from the other optical fiber.

1. High precision, fast response speed, wide range of linear features, good repeatability of use, high signal-to-noise ratio of detection signal, due to the mass production of optical fiber, low price, can be widely used. 2. The optical fiber is made of dielectric material quartz, which transmits optical signals, so it is safe ...

When choosing a pressure sensor, we need to consider its comprehensive accuracy, and what are the aspects that affect the accuracy of the pressure sensor? In fact, there are many factors that cause sensor error, and we will pay attention to four unavoidable errors, which are the initial error of the sensor. Head...

The first point is that photoelectric sensors and fiber optic sensors work differently First of all, from the working principle of the two, first of all, the photoelectric sensor works according to the principle of the photoelectric effect, that is, when the light hits the photoelectric sensor made of semiconductors, it will emit light ...

The 2018 China Automation Industry Annual Conference and the 13th China Automation Industry Century Tour (CAIAC2018) were held on April 12, 2018 at Tianma Hotel, Shaoxing, Zhejiang. CAIAC2018 aims to remember and look forward to China ...

(1) Fork photoelectric sensor Placing an optical transmitter and a receiver facing each other on either side of a slot is a fork photoelectric. The luminaire emits infrared or visible light, and the light receiver receives the light in an unobstructed condition. But when the detected object passes through the slot, the light is blocked ...

A proximity sensor is a device with the ability to perceive the proximity of an object, which uses the sensitivity of the displacement sensor to the approaching object to identify the proximity of the object and output the corresponding switching signal. For this reason, proximity sensors are often referred to as proximity switches. It is an alternative to contact detection ...

General Notes: 1. Avoid pulling, squeezing or twisting the optical fiber cable, do not pull when trying to unwrap the entangled optical fiber cable, you need to be patient and careful to untie it at this time. 2. Avoid sharp bending radius (>50mm) of optical fiber cable. 3. When the conduit is removed from the fiber optic signal demodulator ...

1. Scale determination: identification of the orientation of small parts, monitoring of whether there are parts on the conveyor belt, exploration of material stacking and masking, manipulator orientation (east and west center orientation) control, equipment condition detection, equipment orientation exploration (through small holes), liquid level monitoring, thickness measurement, ...

1. Physical sensor: A physical sensor is a sensor that detects a physical quantity. It is a device that uses certain physical effects to convert the measured physical quantity into a signal in the form of energy that can be easily processed. There is a definite relationship between the output signal and the input signal. The main physical ...

(1) Measurement of absolute air pressure by electronic means makes the control of the inflatable state of the line more complete and continuous. (2) From the dynamic and static aspects, the air leakage point can be estimated in advance. (3) Determine the change in time of the pressure inside the cable, so that the inflatable ...

Depending on the mode of exercise Linear Position Sensor: The function of a linear displacement sensor is to convert the linear mechanical displacement into an electrical signal. In order to achieve this effect, the variable resistance slide rail is usually fixed on the fixed part of the sensor, and the displacement of the slide on the slide rail is measured.

1. The use of ultrasonic spacer sensor skills An ultrasonic sensor consists of three parts: an ultrasonic transducer, a processing unit, and an output stage. First, the processing unit excites the ultrasonic transducer with voltage, and after it is excited, it announces the ultrasonic wave in the form of pulses, and then the ultrasonic transducer is transferred to withstand ...

1. Shielding technology Containers are made of metal materials. Wrapping the circuit that needs to be protected in it can effectively prevent the interference of electric or magnetic fields, and this method is called shielding. Shielding can be divided into electrostatic shielding, electromagnetic shielding and low-frequency magnetic shielding. 2. Electrostatic shielding ...

The photoelectric head of a photoelectric sensor is a precision device, and misalignment can seriously affect the measurement results. This usually happens when external forces interfere with it, such as when the sensor position is shifted due to excessive force during cable construction. At this point, the position of the photohead needs to be readjusted. How to adjust: ...