Fisher/Fisher easy-e EW Series Control Valves

The H200 Series Pop-Up Pressure Relief Valve is a direct-acting pressure relief valve with a pre-installed and fixed spring retaining ring. When the inlet gas pressure exceeds the spring set value, the lift assembly and disc assembly will be pushed away from the valve hole. The H200 Series Pop-Up Pressure Relief Valve is easy to operate and has a spring setting of ...

The Fisher Yarway AT-18/28 Heavy Duty A.T.-Temp Desuperheater was developed specifically for medium/high pressure steam applications. Its prefabricated structure can easily meet a variety of boiler specifications and material specifications. The unit can also be used as an injector for liquid injection gases, typically with high-grade alloys such as stainless steel. ...

Application Flexibility—Actuators can be set either push-down open or push-down shut-off and can be installed anywhere in the four actuator/body mounting positions. Minimized dead zone—single joint connection plus splined pair clamp linkage reduces idling to low and improves control accuracy

N05500 nickel alloy Boton tubes are also available for applications where the controller must meet the NACE MR0175-2002N05500 standard. Repeatability conforms to the Outer Rim of the Continental Shelf (OCS) Order 5 for United States Bureau of Minerals test deviations and the standards defined in the United States Petroleum Organization (API) RP14C.

Introduction: Fisher/Fisher FB welded angle valves control compressible fluids and can be used in special applications that require maximum noise reduction and high flow capacity. Typical applications include main steam pressure reducing valves and compressor bypass valves. FB valves are also commonly used in petrochemical and natural gas processing plants for acidic ...

Fisher DST-G trims are designed for clean or dirty applications where dissolved gases are released from solution when pressure drops (outgassing). Outgassing typically causes two types of damage: cavitation and erosion of the fluid stream. The DST-G trim has a graded pressure drop, similar to the DST trim, to prevent ...

Fisher dirt service trims are designed for dirt and cavitation applications. Cavitation is eliminated with a range of flow limits and extensions, allowing particles up to 19mm (3/4in) in diameter to pass through without clogging. Each trim stage has a sequentially increasing flow ...

The Fisher 2052's highly versatile features and compact actuator design assist with throttling or on/off applications. It can be installed on any valve, even when space is limited. specification Actuation method: spring return, quarter-angle rotation, rotation Certified PED compliant ...

The Model 119 switching valve is used for on/off or throttling control of non-corrosive or slightly corrosive gases. They are designed to meet the requirements of low-pressure gas applications in a variety of industries. The 119EZ and 119EZS are used as fuel gas valves for oil and gas natural draft burners. The product comes with a built-in speed control ...

Fisher Yarway cryogenic injectors have been specifically developed to inject process fluids into process gases at low temperatures. specification Equal percentage of flow characteristics, equal percentages of linearity, correction, etc., specialization Materials: 304 stainless steel, 316L stainless steel, 316 stainless steel The operating temperature is ultra-low ...

The Fisher V260 is a full-bore control valve with a bottom-up design that maximizes pressure, flow, and process control. Integral borehole silencers are used to control noise and vibration generated by high-pressure drop liquids and gases. The spline shaft is connected with the actuator, which reduces the movement loss. ...

The Fisher Model 63EG Pilot-Operated Pressure Relief Valve can be used in both liquid and gas applications. The 63EG is also suitable for throttling back pressure or bypass applications. Both main valves use quick-change spool packs for quick maintenance. For remote monitoring, the Model 63EG valve can be used with position monitoring.

The 44-1300 Series is a high-pressure, high-flow pressure reducing valve that offers both bleed and balanced spool designs. The 44-1300 series is available with Cv = 0.8 and 2.0. Chamber-loaded and pneumatically compressed load models are available. Ideal for commercial diving, breathing air, special gas mixture regulation, rigid kit diving...

The Model 252 filter is designed to clean supply gas or air in a pilot, pneumatic instrument, or other device that requires clean gas to function properly when it is about to enter a pilot-acting regulator. This is an extended version of the filter with a larger drainage chamber that can hold more moisture and ...

The Model R232A regulator is certified by Underwriters Laboratories (United States Safety Testing Laboratories, Inc.) for use in LPG systems. The regulator is designed to reduce tank pressure through an integrated two-stage system that provides an 11-inch water column of outlet pressure. For the people ...

Available in lead-free versions to comply with the Safe Drinking Water Act, cryogenic models can control cryogenic fluids, including liquid nitrogen (-320° F/-194° C), liquid argon (-303° F/-184° C), and liquid oxygen (-297° F/-181° C) for washing machines, boilers, and thermal applications.

The 627 series regulator is a direct-operated regulator that can be used in low and high pressure systems, in small towns or small urban gas stations for regulation, regulation and bleed valve systems, monitoring regulator systems, or for high-pressure industrial gas stations. Fisher Fisher 627 Series Straight ...

Introduction: The Fisher/Fisher A11 High Performance Butterfly Valve is a reliable, high-performance butterfly valve for throttling and switching applications. Available in a pair of clamp or single flange designs to maintain tight shut-off over long periods of time, the valve is specific for a wide range of pressure and temperature conditions, including cryogenic applications.

The 670 Series Panel Mount Regulator is a compact and rugged unit designed primarily for manually loaded pressure-balanced gas regulators to provide manual control of the diaphragm actuator control valve. peculiarity Control flexibility Easy fingertip control Easy to connect specification Maximum inlet pressure without shear ...

The Fisher 656 diaphragm actuator provides low- to medium-thrust actuation for stent-mounted applications. Such applications include the operation of butterfly valves and built-in turbine valves, louvers, dampers, and other similar equipment. specification Actuation mode: spring return, linear Certified PED, CUTR, ATEX Control...